[See subsections ...]
Search Results "Wheelchair Space (Assembly)"
2010 ADA Definition
Wheelchair Space (Assembly): Space for a single wheelchair and its occupant.
Filters
Commonly Searched Documents
-
ABA CHAPTER 8: SPECIAL ROOMS, SPACES, AND ELEMENTS
-
4. ACCESSIBLE ELEMENTS AND SPACES: SCOPE AND TECHNICAL REQUIREMENTS
[See subsections ...]
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors. The width of the level area at the exterior side...
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors. The width of the level area at the exterior side...
-
Pilot Rock UT Series Side Accessible Picnic Table Using Recycled Plastic
A section of seating is removed from the side(s) for ADA COMPLIANT wheelchair accessibility right in the middle of activities. ...
-
216.12 Amusement Rides
Amusement rides designed primarily for children, amusement rides that are controlled or operated by the rider, and amusement rides without seats, are not required to provide wheelchair spaces...
-
Accessible Routes - Interior and Exterior
and sidewalks to the accessible entrance(s), and the interior routes (e.g., hallways and corridors) throughout the lodging facility, are not usable by persons who use wheelchairs or other...
-
Clear Tread Width [1017.3]
Where gates and barriers require users to make 90-degree or 180-degree turns, sufficient space should be provided for people using mobility devices to make the turns (figure 3)....
-
Slope : Intercept
They form a suite of objects for installation in public space, both as a mode of critical play and critical access....
-
Safe Harbor
Examples The 1991 Standards required one van-accessible space for every eight accessible spaces....
-
11B-202.3 Alterations
Where existing elements or spaces are altered, each altered element or space shall comply with the applicable requirements of Division 2, including Section 11B-202.4....
-
Station 1-Physical Characteristics
Wheel spacing-measured from the center of one outside wheel to the center of the other outside wheel....
-
2.2 Key Measurement Variables and Procedures
Demographic information and wheelchair description: Approximately 30 variables recorded with a checklist, along with digital still photographs of the user and mobility device. 2....
-
3.3.11 180-Degree Turn
The space requirements for a 180-degree turn are similar across countries, ranging from 1500 mm (59 in.) in the U.K. and Canada to 1540 mm (60.6 in.) in Australia....
-
9. Exterior Ramps
have the following features: a. top and bottom landings that are level, at least as wide as the ramp they serve, and at least 60" long to allow for adequate maneuvering and resting space...
-
Kitchen Cabinets
With a remodel, they can be lowered to 32” a.f.f. for wheelchair users 10” removable drawer in the kick space to lower the cabinets for wheelchair users Self-closing drawers...
-
Accessible Routes
Accessible Routes An accessible route is a pathway specifically designed to provide access for individuals with disabilities, including those using wheelchairs or mobility devices....
-
M304 Diagnostic Equipment Used by Patients in Standing Position
., standing position, seated position, and seated in a wheelchair)....
-
F202.3 Alterations
Where existing elements or spaces are altered, each altered element or space shall comply with the applicable requirements of Chapter 2. EXCEPTIONS: 1....
-
16. If a play surface is replaced with an accessible surface and the existing ground level play components are not accessible, do the components need to be replaced?
If the alteration to the play area only involves the surfacing, only the surface along accessible routes, clear floor or ground spaces, and maneuvering spaces must comply with the ASTM F...
-
Kompan, Inc. Electronic Playgrounds ICON1012 Space Video
This is a short video of the electronic interactive play ground equipment by Kompan Inc.
-
11B-411.2.1.3.4 Position
The face of hall call console assemblies and the face of touch screens shall be sloped away from the user at 7 to 25 degrees from the vertical plane....
-
Press Boxes [§206.2.7]
Press Boxes [§206.2.7] An accessible route is required to press boxes except where the aggregate area of all press boxes serving a playing field or assembly area is no more than 500 sq...
-
Table of Contents
Fire Alarm Systems F216 Signs F217 Telephones F218 Transportation Facilities F219 Assistive Listening Systems F220 Automatic Teller Machines and Fare Machines F221 Assembly...
