Sliding door bath tub with pressure sealed door, made of gelcoat / fiberglass construction with access panel for access to plumbing and electrical components....
Search Results "Door Clear Width"
Filters
Commonly Searched Documents
-
Best Bath Systems ADL Spa Electronic Touch Control Series Slide-Door Bath Tub
-
Basic Features
Careful planning and design will incorporate elements such as a wider entrance door, adequate clear floor space, appropriate placement and models of fixtures and furniture, and grab bars...
-
H15
Is at least one wide toilet stall provided with an out swinging door, side and rear grab bars, and clear space next to the toilet?...
-
809.2.5 Bedrooms in Emergency Transportable Housing Units
Where bedrooms are less than 70 square feet, the section specifies that the furniture supplied with the unit cannot overlap the accessible route, maneuvering clearances required at doors...
-
T-turn Maneuvering Space
The Guidelines adequately address the accessible route into and through the dwelling unit by the minimum corridor width and door width specifications, given typical apartment layouts....
-
9.4 POST OFFICE BOXES
Aisles between post office boxes shall be a minimum of 66 in (1675 mm) clear width....
-
Common Problems with Toilet Rooms
is not enough maneuvering space immediately inside or outside the toilet room door for a person using a wheelchair to open and pass through the door. ...
-
A4.29.3 TACTILE WARNINGS ON DOORS TO HAZARDOUS AREAS
Tactile signals for hand reception are useful if it is certain that the signals will be touched.
-
Activar JL Industries ORBIT SERIES - LOW PROFILE CABINET
Door and Trim Construction: Flush cabinet doors with a 5/8" door stop are attached by a continuous hinge and equipped with zinc-plated handle and roller catch....
-
1134A.8, Item 4.3
Doors to the cabinet beneath the lavatory shall be removable or openable to provide the required unobstructed knee and toe space....
-
1134A.8, Item 4.3
Doors to the cabinet beneath the lavatory shall be removable or openable to provide the required unobstructed knee and toe space....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
Door King Inc. 1520/1524 Stand Alone Card Readers
The model 1520 provides users with a full feature single door stand-alone access control system....
-
BHMA
ANSI/BHMA A156.10-1999 American National Standard for Power Operated Pedestrian Doors (see 404.3)....
-
1134A.5 Bathtubs
The edge of the clear floor space shall be flush with the control wall surface....
-
Mounting Height and Location
Tactile signs are required to be located alongside the latch side of doors so that clear floor space at least 18 by 18 inches, centered on the tactile characters, is provided outside the...
-
Door King Inc. 6050 / 6100 Residential and Commercial Swing Gate Operator
Specifications: Model 6050 Maximum gate width 10-feet. Maximum gate weight 400 pounds*. ...
-
2.2.4 Maneuverability
Widths of the restricted space were set at a minimum of 750 mm (30 in.) for the 90-degree turn, 750 mm (30 in.) passage width for the U-turn with a barrier, and 1300 mm (51 in.) for the...
-
Rockwood Manufacturing Company K1038 .038" Thick - Metal Kick Plate
Width of Plates: Push Side: 2" less than door width. Pull Side: 1-1/2" less than door width....
-
Jean Tessmer
I have specified and had this particular pocket door privacy latchset installed in new construction where I did not have enough door clear floor space for a swing door....
-
California Water Closet Accessories
Design guidance for locating water closet accessories in single user toilet rooms and best practice placement of the lavatory in new construction giving the owner more options to...
-
11B-812.10.4 Location
EV chargers shall be adjacent to, and within the projected width of, the vehicle space being served....
-
General: ADA Standard Section 502.1
Section 502.1 of the ADA Standards covers information in the current ADA Standards for accessible parking spaces.
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
