A clear maneuvering space at least 30 inches by 48 inches (762 mm by 1219 mm) shall be provided at lavatories and shall be centered on the lavatory. 3. Cabinets....
Search Results "Clear Width at Turn"
-
1134A.8 Lavatories, vanities, mirrors and towel fixtures
- Ronick Matting Systems BaseMat 300 Entrance Floor Mat
- Inclusion Solutions Freestanding Totem Pocket Display
- Grainger Soap Dispenser, 800mL, Ceramic White
- Inclusion Solutions Frankie Adjustable Single Voting Booth
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
308.2.2 Obstructed High Reach
Where a high forward reach is over an obstruction, the clear floor space shall extend beneath the element for a distance not less than the required reach depth over the obstruction....
-
R212 Street Furniture (Section-by-Section Analysis)
At least 50 percent, but no less than one, of benches at each location must provide a clear space for a wheelchair adjacent to the bench. Benches at tables are not required to comply....
-
On-Site Readers
Specific skills are needed to be an on-site reader: ability to read material well, a good clear voice, and, ideally, knowledge of the language and vocabulary used in the documents....
-
11B-904.4 Sales and service counters
the number of existing mail boxes, the counter shall be permitted to have a portion which is 24 inches (610 mm) long minimum complying with Section 11B-904.4.1 provided that the required clear...
-
11B-904.4 Sales and service counters
the number of existing mail boxes, the counter shall be permitted to have a portion which is 24 inches (610 mm) long minimum complying with Section 11B-904.4.1 provided that the required clear...
-
1007.2 Accessible Routes
Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum. 3....
-
Section B: Passenger Drop-Off Area
(§§206.2.1, 503.3) B5 Is the width of the curb ramp surface at least 36” (not counting the side flares)?...
-
Study Objectives
Seat widths needed for each level, highest and lowest transfers to i) a seat with no handhelds present, ii) a seat with grab-bars and iii) a seat with grab-bars and a backrest c....
-
4.1.2 Number of Wheelchair Seating Spaces
Number of Wheelchair Seating Spaces Table Top Perimeter Typical Table Length (for 2 ft. 6 in. table width) Number of Wheelchair Seating Spaces Required Up...
-
Engineered Surfaces
Table 3: Engineered Surface Identification Surface ID: Roughness Index (in/ft): Crack Frequency (in): Crack Width (in):...
-
Is compliance required for parking spaces designed specifically for recreational vehicles such as motor homes and camping or boating trailers?
The ABA Standards address access to RV and other parking spaces at camping and picnic units and pull-up spaces at dump stations and cover space width (minimum 20’, or 16’ in the case of...
-
1.1.5 Flatness of walk running slope
For pedestrian paths up to and including 6 ft (1.8 m) wide, measure for flatness of the running slope at 10 ft (3 m) increments along the midpoint of the width of the walk by using a 10...
-
11B-1007.2 Accessible routes
Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (813 mm) minimum....
- Pilot Rock T300/T400 Series Round, Pedestal Table With CONTOUR Bench Seats - Using Expanded Steel
-
11B-233.3.6 Graduate student and faculty housing at a place of education
(1) In sleeping rooms with more than 25 beds covered by this part _|of the Title III regulation or to this section of the title II regulation|_, a minimum of 5% of the beds shall have clear...
-
4.2 Applications of Findings in Design and Standards Development
However, there are some cases in which the implications are much broader, for example, length of clear floor area, knee and toe space clearances, 360-degree turning space, and front reach...
-
5. Compare Surface Options
Results of ASTM F1951-99 laboratory tests, including the values for the baseline, straight propulsion and turning runs....