Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
Search Results "Water Pump"
Filters
Commonly Searched Documents
-
11B-604.3.1 Size
-
11B-604.3.1 Size
Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
-
Dimensions for Adults and Children: ADA Standard Section 102
Section 102 of the ADA Standards covers information on the dimensions for adults and children.
-
11B-102 Dimensions for adults and children
In addition, this chapter includes technical requirements based on children’s dimensions and anthropometrics for drinking fountains, water closets, toilet compartments, lavatories and sinks...
-
604.8.1.5 Grab Bars
A side-wall grab bar complying with 604.5.1 shall be provided and shall be located on the wall closest to the water closet....
-
Position of Grab Bars: ADA Standard Section 609.4
Section 609.4 covers the current ADA Standards for the position of grab bars.
-
6. Clear floor space
6. Clear floor space: Adequate space is provided to approach the toilet from a variety of wheelchair transfer positions (i.e. diagonal or side approaches). Generally, the toilet...
-
4. Toilet seat height
4. Toilet seat height: The toilet seat needs to be from 17 to 19 inches above the floor to permit transfers to and from wheelchairs.
-
Note
Note: In every instance, regardless of toilet and lavatory configuration, adequate space needs to be provided for inmates who use wheelchairs to transfer onto and off of the...
-
M8
M8. Is there at least 18 inches between the center of the toilet and the side of the adjacent lavatory? [ADA Standards § 4.16.2; Fig. 28] Yes No
-
4.15.4 Controls
Controls shall comply with 4.27.4. Unit controls shall be front mounted or side mounted near the front edge.
-
Controls [4.15.4]
Controls [4.15.4] Controls must be operable with one hand and not require tight grasping, pinching, or twisting of the wrist to operate. Push bars are easier to use by a broader...
-
A4.16.3 Height
Height preferences for toilet seats vary considerably among disabled people. Higher seat heights may be an advantage to some ambulatory disabled people, but are often a disadvantage...
-
A4.16.3 HEIGHT
Preferences for toilet seat heights vary considerably among disabled people. Higher seat heights may be an advantage to some ambulatory disabled people but a disadvantage for...
-
4.15.4 CONTROLS
Controls shall comply with 4.27.4. Unit controls shall be front mounted or side mounted near the front edge.
-
5.3.3.1 Height
The total height of the toilet seat on the riser for a pit toilet shall be between 17 inches (430 mm) and 19 inches (485 mm) above the floor or ground surface.
-
Length
Length. Whereas none of the respondents specifically addressed the issue of grab bar length, drawings submitted clearly indicate that many of the alternate swing away grab bars were...
-
Offset Flange
For floor mounted water closets, we have suggested the use of an offset waste flange to shift the centerline. ...
-
Pool Lifts
Pool Lifts Pool lifts must be located where the water level is not deeper than 48 inches....
-
11B-609.4 Position of grab bars
shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except that at water...
-
American Standard Commercial Toilet Seat for Baby Devoro Bowls
For Baby Devoro bowls 2315.228 and 2282.001 Open front toilet seat less cover Available in White (020) Injection molded solid polypropylene EverClean® antimicrobial...
-
Whitehall Mfg. WH2105BAR Bariatric Toilet Siphon Jet Type Off-Floor
14 gage 304 stainless steel off-floor Siphon Jet toilet features reinforced housing to withstand up to 1,000 lbs with optional carrier. Product Details Material: ...
-
Whitehall Mfg. WH2125A On-Floor Bariatric Stainless Steel Toilet
This bariatric toilet is designed to be installed on a finished wall either from the front or in a rear (chase) application. The unit is fabricated of 14 gage, type 304 stainless...
-
11B-604.3.1 Size
Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
