All walks with continuous gradients shall have resting areas, 60 inches (1524 mm) in length, at intervals of 400 feet (121,920 mm) maximum....
Search Results "Walking Surface"
Filters
Commonly Searched Documents
-
11B-403.7 Continuous gradient
-
4.3.4 Tent Pad or Platform Surface
Tent pads and platforms shall have a surface that is firm and stable and is designed to allow use of tent stakes and other tent securing devices. Exception....
-
2. Typical Issues for Individuals Who Are Blind or Have Low Vision
Since people can walk on any sidewalk, not just the accessible routes, all exterior pedestrian routes serving or leading to the shelter areas must be checked....
-
General: ADA Standard Section 401
Section 401 of the ADA Standards covers information in the current ADA Standards for accessible routes.
-
11B-401 General
[See subsections ...]
-
AccessRec AccessMat Beach Access Mat System
Comfortable and Safe Developed specifically for pedestrian traffic, AccessMat™ provides a barefoot friendly surface for beach goers....
-
810.2.1 Surface
810.2.1 Surface. Bus stop boarding and alighting areas shall have a firm, stable surface....
-
Surface
The top layer of a trail.
-
1002.4.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall be stable and firm....
-
1002.4.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall be stable and firm....
-
KirbyBuilt Providence Walk-Thru Picnic Table
Convenient walk-thru design accommodates 1 wheelchair. Tabletop & Seats: Plastic - injection molded, ribbed & reinforced Tabletop Length: 8 ft....
-
4.4.6 Surface
The surface of the clear floor or ground space for benches shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
Beneficial Designs The Universal Trail Assessment Process (UTAP)
Illustrated step-by-step instructions show how to use each assessment tool, how to accurately measure grade, cross slope , width, and obstacles and how to describe surface type....
-
802.1.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
802.1.1 Floor or Ground Surface
The floor or ground surface of wheelchair spaces shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
Surface
Surface—The top layer of ground on a recreation site, outdoor recreation access route, trail, or beach access route Firm. A surface that resists deformation by indentations....
-
Surface, Slope, and Openings [1011.2.2, 1011.2.3, and 1011.2.4]
The surface of the clear ground space must be firm and stable. Additional information on firm and stable surfaces is provided in the trails section of this guide....
-
T208 Passenger Access Routes
[See subsections ...]
-
4.3.6 Surface Textures
The surface of an accessible route shall comply with 4.5....
-
4.3.6 SURFACE TEXTURES
The surface of an accessible route shall comply with 4.5....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
b. Transfer Surface Location
The MDE NPRM proposed the same location and transfer sides of the transfer surface for diagnostic equipment used by patients in the supine, prone, or side-lying position (M301) and diagnostic...
