Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
Search Results "Handrail Height"
Filters
Commonly Searched Documents
-
11B-505.7.2 Non-circular cross sections
-
11B-703.8.4 Character height
The uppercase letter “I” shall be used to determine the allowable height of all low resolution VMS characters of a font....
-
505.7.2 Non-Circular Cross Sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (100 mm) minimum and 6 1/4 inches (160 mm) maximum, and a cross-section dimension...
-
505.7.2 Non-Circular Cross Sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (100 mm) minimum and 6 1/4 inches (160 mm) maximum, and a cross-section dimension...
-
5.3.3.1 Height
The total height of the toilet seat on the riser for a pit toilet shall be between 17 inches (430 mm) and 19 inches (485 mm) above the floor or ground surface....
-
Clearances between a handrail and wall surface: 2012 NFPA 101 vs. 2010 ADA
Question/Issue: According to the new 2012 NFPA 101 Life Safety Code, Chapter 7, Section 7.2.2.4.4.5 & Exhibit 7.97, the finger clearance at an existing stair handrail should be...
-
11B-606.3 Height
ETA Editor's Note Top-mounted sinks installed in counters having the top surface 34 inches above the floor will exceed the maximum rim height allowed, regardless of how thin the flange...
-
11B-606.3 Height
ETA Editor's Note Top-mounted sinks installed in counters having the top surface 34 inches above the floor will exceed the maximum rim height allowed, regardless of how thin the flange...
-
1009.2.4 Seat Height
1009.2.4 Seat Height....
-
Aisle Stairs and Ramps in Assembly Areas
Sections 505.2 and 505.3 of the 2010 Standards provide exceptions for aisle ramp handrails....
-
§ 38.25(c) Door height
(c) Door height....
-
Height Above Finish Floor or Ground: ADA Standard Section 703.4.1
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60...
-
Figure 505.6 Horizontal Projections Below Gripping Surface – Drawing from the U.S. Access Board
-
T702.4 Character Height
Character height shall comply with Table T702.4. Character height shall be based on the uppercase letter “I”....
-
Character Height [4.30.3]
Character Height [4.30.3] Characters must be sized according to the viewing distance although a minimum 3 inch upper case or capital letter height is required for overhead signs (i.e....
-
1009.2.4 Seat Height
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
606.3 Height
606.3 Height. Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (865 mm) maximum above the finish floor or ground....
-
11B-813.2.1.3 Height and operation
Adult changing table height shall be adjustable from 17 inches (432 mm) above the floor or ground to 38 inches (965 mm) above the floor or ground, as measured to the top of the changing...
-
Can stair handrail extensions overlap door maneuvering clearances?
No, handrails and other elements cannot overlap door maneuvering clearances....
-
Addendum F: Relative Height Differences
Relative heights were calculated for high and low transfers for all three protocols. Refer to Addendum A for the definition of relative height....
-
R409.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
§ 38.155(a)
(a) Handrails and stanchions shall be provided in the entrance to the vehicle in a configuration which allows passengers to grasp such assists from outside the vehicle while starting to...
-
T207.1 General
Non-rail vehicles shall provide handrails, stanchions, and handholds in accordance with T207. Handrails, stanchions, and handholds shall comply with T303....
-
4.16.3 Height
4.16.3 Height. All of the institutional designs included a raised toilet within the 17"-19" range allowed by ADAAG....
