Where components of ICT are hardware and transmit information or have a user interface, such components shall conform to applicable requirements in Chapter 4....
Search Results "Door Hardware"
Filters
Commonly Searched Documents
-
E206.1 General
-
1132A.2 Interior doors and secondary exterior doors
Except as allowed by Section 1109A.2, interior doors intended for user passage and secondary exterior doors shall comply with this section....
-
1132A.2 Interior doors and secondary exterior doors
Except as allowed by Section 1109A.2, interior doors intended for user passage and secondary exterior doors shall comply with this section....
-
206.5 Doors, Doorways, and Gates
206.5 Doors, Doorways, and Gates. Doors, doorways, and gates providing user passage shall be provided in accordance with 206.5....
-
404.2.6 Doors in Series and Gates in Series
404.2.6 Doors in Series and Gates in Series....
-
404 Doors, Doorways, and Gates
404 Doors, Doorways, and Gates...
-
AUTOMATIC DOOR
A door equipped with a power operated mechanism and controls that open and close the door automatically upon receipt of a momentary actuating signal....
-
AUTOMATIC DOOR
A door equipped with a power operated mechanism and controls that open and close the door automatically upon receipt of a momentary actuating signal....
-
Are closet doors and pantry doors required to comply?
Requirements for doors, doorways, and gates in §404 apply to those that provide “user passage” (§206.5). Doors serving walk-in closets or pantries must comply....
-
11B-411.3.2 Operation
Elevator hoistway and car doors shall open and close automatically....
-
18.1 Q. Is it necessary to provide usable doors when the door leads to an area of the dwelling that is not accessible, such as the door leading down to an unfinished basement...?
Within the dwelling unit, doors intended for user passage through the unit must meet the requirements for usable doors....
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
F206.5 Doors, Doorways, and Gates
Doors, doorways, and gates providing user passage shall be provided in accordance with F206.5....
-
206.5 Doors, Doorways, and Gates
Doors, doorways, and gates providing user passage shall be provided in accordance with 206.5....
-
Doors, Doorways and Gates [§206.5 and §404]
Doors, Doorways and Gates [§206.5 and §404] Compliance is required for doors, doorways, and gates providing user passage on accessible routes....
-
R218 Doors, Doorways, and Gates
R218 Doors, Doorways, and Gates The SNPRM would revise R218 to read as follows: R218 Doors, Doorways, and Gates....
-
Open Doors Organization (ODO)
Open Doors Organization (ODO), a 501(c)(3) non-profit organization based in Chicago, Illinois was founded in 2000 for the purpose of creating a society in which all persons with disabilities...
-
C204.1 General
Where components of ICT are hardware, and transmit information or have a user interface, those components shall conform to applicable requirements in Chapter 4....
-
11B-809.8.3 Door maneuvering clearance.
At the dwelling unit side of the primary entry doors, secondary exterior doors, and required exit doors maneuvering clearances shall be 44 inches (1118 mm) minimum in length measured...
-
Hager Companies Round Wrought Door Push/Pull Set 14
Round Wrought Door Push/Pull Set Materials: - Aluminum, brass, bronze, stainless steel Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Round Wrought Door Push/Pull Set 13
Round Wrought Door Push/Pull Set Materials: - Aluminum, brass, bronze, stainless steel Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Door Pull 974P
Door Pull 974P Pull Material:- Brass, bronze, stainless steel...
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
Door and Signal Timing for Hall Calls [4.10.7], Door Delay for Car Calls [4.10.8]
Timing, based on the distance between the farthest call button and the elevator door, begins with visible and audible signaling of car arrival....
