M305.2.1 would require the transfer supports to be located within reach of the transfer surface and not obstruct transfer onto the surface when in position....
Search Results "Surface Slope"
Filters
Commonly Searched Documents
-
Transfer Supports (M301.3.1, M302.3.1, and M305.2)
-
Clearance in Base (M301.4.1 and M302.4.1)
would require the clearance in the base to be 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination surface...
-
Time periods
establishes accessibility requirements for new construction and alterations, requires that all newly constructed or altered streets, roads, or highways must contain curb ramps or other sloped...
-
11B-206.2.1 Site arrival points
(1) Newly constructed or altered streets, roads, and highways must contain curb ramps or other sloped areas at any intersection having curbs or other barriers to entry from a street...
-
11B-206.2.1 Site arrival points
(1) Newly constructed or altered streets, roads, and highways must contain curb ramps or other sloped areas at any intersection having curbs or other barriers to entry from a street...
-
1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface....
-
403.5.1 Clear Width
Except as provided in 403.5.2 and 403.5.3, the clear width of walking surfaces shall be 36 inches (915 mm) minimum....
-
1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface....
-
1009.5.4 Transfer Steps
The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level. Advisory 1009.5.4 Transfer Steps....
-
R406.3 Unobstructed Side Reach
approach to an element and the side reach is unobstructed, the high side reach shall be 1220 mm (4.0 ft) maximum and the low side reach shall be 380 mm (1.25 ft) minimum above the finish surface...
-
4.1.7(3)(e)
., open books), should be no higher than 44 in (1120 mm) above the floor surface....
-
Wheelchair Work Measurement Method
Wheelchair work per meter values for straight and turning were determined for all test course surfaces except sand, under dry conditions using the Wheelchair Work Measurement Method in accordance...
-
Fixed tactile maps
Placement on a horizontal or near horizontal surface provides the map reader with a real world orientation....
-
6.9 Tread Obstacles
Where the surface is paved or is elevated above the natural ground, obstacles shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
11B-704.5 TTY shelf
The telephone handset shall be capable of being placed flush on the surface of the shelf....
-
1007.1 Accessible means of egress required
In assembly areas with sloped or stepped aisles, one accessible means of egress is permitted where the common path of travel is accessible and meets the requirements in Section 1028.8, and...
-
Shower Threshold
The proposed rule specified a maximum threshold height of ½ inch, provided that those greater than ¼ inch are beveled with a slope of 1:2 maximum (608.7)....
-
Fishing piers and platforms. (Section-by-Section Analysis)
attached to land) are involved, a number of exceptions are provided from the general standards for accessible routes in order to take into account the difficulty of meeting accessibility slope...
-
Fishing piers and platforms. (Section-by-Section Analysis)
attached to land) are involved, a number of exceptions are provided from the general standards for accessible routes in order to take into account the difficulty of meeting accessibility slope...
-
Technical Infeasibility
plumbing, life safety or other codes (such as when combining two toilet stalls to create an accessible stall would violate the plumbing code’s required fixture count); meeting slope...
-
Allegion Falcon 2390 Series Recessed Exit Device
End Caps: Sloped metal end caps ANSI: Certified ANSI A156.3 Grade 1 standards Vertical Rods: 7' standard, extension rods available up to 10'....
-
Table of Contents
Assembly Areas F222 Dressing, Fitting, and Locker Rooms F223 Medical Care and Long-Term Care Facilities F224 Transient Lodging Guest Rooms F225 Storage F226 Dining Surfaces...
