ILLUSTRATION: An individual who uses a wheelchair may be excluded from playing in a basketball league, if the recreation center can demonstrate that the exclusion is necessary for safe operation...
Search Results "Recreational Surfacing"
Filters
Commonly Searched Documents
-
III-3.4200 Right to participate in the regular program
-
SECTION 1017 AISLES
for applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, shall also comply with Chapter 11A or Chapter 11B, Section 11B-403 _|Walking Surfaces...
-
11B-307.3.1 Edges and corners
Where signs or other objects are mounted on posts or pylons, and their bottom edges are less than 80 inches (2032 mm) above the floor or ground surface, the edges of such signs and objects...
-
505.10.3 Bottom Extension at Stairs
Extension shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent stair flight....
-
1009.5.2 Transfer Space
A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
Width and Length
This provides enough space for a person to sit comfortably on the surface of the wall and pivot to access the water....
-
Maneuvering Space Where Ramps are Provided
The ADA and ABA Accessibility Guidelines address additional requirements for ramps and landings including edge protection, cross slope, surfaces, and outdoor conditions....
-
505.10.1 Top and Bottom Extension at Ramps
Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent ramp run....
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
505.10.1 Top and Bottom Extension at Ramps
Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent ramp run....
-
505.10.2 Top Extension at Stairs
Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent stair flight....
-
R305.2 Placement
The placement of detectable warning surfaces shall comply with R305.2. Advisory R305.2 Placement. Some detectable warning products require a concrete border for proper installation....
-
Seating [4.32.2] and Knee Clearance [4.32.3]
The over-the-surface reach is limited to 25 inches if at least this much space is available below for knees and toes; (the forward seated reach may not extend beyond the toes)....
-
1018.10 Dune Crossings
The curbs or barriers are required to prevent the passage of a 2 inch diameter sphere, where any portion of the sphere is within 2 inches of the crossing surface....
-
11B-1009.5.2 Transfer space
A transfer space of 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
§ 38.119(b)
doorways of cars not operating at lighted station platforms shall have outside lights which, when the door is open, provide at least 1 foot-candle of illumination on the station platform surface...
-
§ 38.81(c)
(c) The doorways of vehicles not operating at lighted station platforms shall have outside lights which provide at least 1 foot-candle of illumination on the station platform or street surface...
-
11B-407.4.6.2.1 Size and shape
Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
11B-1009.5.2 Transfer space
A transfer space of 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
Industry Standards
Test Method for Determining Floor Tolerances Using Waviness, Wheel Path and Levelness Criteria (Metric) ASTM F 802-83(2003) Standard Guide for Selection of Certain Walkway Surfaces...
-
4. Organization of Technical Criteria
For example, X-ray equipment that is designed for use in a standing position for certain procedures would have to meet the technical criteria for slip resistant standing surface and standing...
-
218 and 810 Transportation Facilities
Detectable warnings provide a distinctively textured surface of truncated domes....
-
QUESTION: WHAT CONSTITUTES AN ALTERATION TO A PLATFORM FOR PURPOSES OF TRIGGERING THE APPLICATION OF SECTION 37.42 REQUIREMENTS?
For example, if the platform height relative to the top of rail is raised, if the old surface is removed and/or a new surface put down, or if there is a reconstruction of or structural change...