Model 357 Surface Mounted 6.5 Gallon Capacity BradEX...
Search Results "Surface Hazard"
Filters
Commonly Searched Documents
-
Bradley 6.5 Gallon Waste Receptacle 357
-
ACCESSIBILITY
For example, concrete play areas are being replaced by soft surfaces to reduce child injury....
-
11B-1003.3.2 Boarding pier clearances
At high water, the entire chain is floating and a transition plate connects the first float to the surface of the launch ramp....
-
Bradley 12 Gallon Waste Receptacle
-10, 346-11 Satin finish stainless steel Model 346: Recessed (projects 2-3/4") Model 346-10: Semi-recessed (recesses 4", projects 4-3/4") Model 346-11: Surface-mounted...
-
Bradley High Capacity Towel Dispenser / 4.9 Gallon Waste Receptacle 2017
towels 4.9 gallon waste capacity Model 2017 - Recessed - BradEX Model 2017-10 - Semi-recessed (recesses 3-1/2"; projects 2-1/2") BradEX Model 2017-11 - Surface...
-
Pressalit Care VALUE Support Arm Height Adjustable
Incl. fixing kit for brick wall Basic material: Steel Surface material: Rilsan End cap: Nylon (PA) Provides firm support when you are sitting, standing, or transferring to and...
-
11B-704.4.1 Height
When in use, the touch surface of TTY keypads shall be 34 inches (864 mm) minimum above the finish floor. [S.H. ...
-
Sections 505.10.2 and 505.10.3
Commenters noted that the 2010 Standards will require handrail gripping surfaces with a circular cross section to have an outside diameter of 2 inches, and that this requirement would impose...
-
Q5: Effective Date for Public Entities to Comply
This technical assistance was provided to respond to questions that arose largely due to the development of a variety of road surface treatments, other than traditional road resurfacing,...
-
604.7 Dispensers
paper dispensers are installed above the side wall grab bar, the outlet of the toilet paper dispenser must be 48 inches (1220 mm) maximum above the finish floor and the top of the gripping surface...
-
Baby Changing Tables
In addition, convenience fixtures, such as baby changing tables, must be accessible to persons with disabilities under scoping provisions for operable parts (205) and work surfaces (226)...
-
M303.2.2 Width (Section-by-Section Analysis)
an exception in the final rule that permits wheelchair spaces on raised platforms to be 32 inches wide minimum with edge protection no higher than 4 inches, measured from the platform surface...
-
1127B.5, Item 4
A level landing 4 feet (1219 mm) deep shall be provided at the upper end of each curb ramp over its full width to permit safe egress from the ramp surface, or the slope of the fanned or...
-
Technical Memorandum TM 2013-22 Storage (Kitchens and Kitchenettes)
Counter surfaces shall not be considered shelf space nor used to satisfy the requirements of 804.5....
-
1017.4 Passing Spaces
at shorter intervals if the clear tread width is less than 60 inches (1525 mm), where a trail is: --Heavily used; or --A boardwalk or otherwise not at the same level as the ground surface...
-
5.8.1.2 Entry to Wheelchair Spaces on Raised Platforms
5.8.1.2 Entry to Wheelchair Spaces on Raised Platforms Recommendations Description: Entry to wheelchair spaces on raised surfaces greater than ¼ inch in height requires a transition...
-
CONTENTS
Increasing number of Health Care Providers are Transitioning to Adjustable Height Tables Available data do not support departing from the currently accepted standard of 19-Inch transfer surface...
-
Implementation Challenges for Interiors (slides 16 and 17)
In the past, [we] have been required to have truncated cones covering the entire surface. For someone in a wheelchair, that is literally hell....
-
Disorienting Spaces (slide 7)
It’s actually a flat surface, and then going into the lovely, also very easy-to-navigate checkerboard flooring pattern....
-
1017.4 Passing Spaces
at shorter intervals if the clear tread width is less than 60 inches (1525 mm), where a trail is: • Heavily used; or • A boardwalk or otherwise not at the same level as the ground surface...
-
Beach Access Routes
Beach access routes provide a firm and stable surface over the sand and are used by beach visitors with and without disabilities....
-
Construction Specification Institute
Construction Specification Institute While developing suggested tolerances for surface materials, the Construction Specifications Institute developed a suggested method for measuring ramp...
-
1.1.1
The simplest way for design professionals to avoid problems with construction tolerances related to surface accessibility and other accessible elements is to design for slopes and dimensions...
-
Other Sources
The Access Board used anthropometric data and other standards for the width of transfer surfaces on diagnostic equipment used by patients in a seated position (see M302.2.2), height of breast...
