the surface....
Search Results "Ramp Surface"
-
Stabilizer
-
How is slip resistance measured?
The coefficient of friction between the two surfaces is the ratio of the horizontal and vertical forces required to move one surface over another to the total force pressing the two surfaces...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
Detectable Warning
A standardized surface feature built in or applied to walking surfaces or other elements to warn visually impaired people of hazards on a circulation path....
-
TACTILE WARNING
A standardized surface texture applied to or built into walking surfaces or other elements to warn visually impaired people of hazards in the path of travel....
-
StaLok
During the testing performed in August 2007, it was noted that an individual had walked on the surface at the Wetlands dedication and left marks in the surface of a depth of approximately...
-
Components (R302.2) (Section-by-Section Analysis)
Curb ramps and blended transitions must comply with the technical requirements in R302.7 and R304. Ramps must comply with the technical requirements in R407....
-
Scoping [4.1.3(4)]
Stairs do not have to comply where vertical access (ramp, elevator, or lift) is provided....
-
303.3 Beveled
Changes in level exceeding 1/2 inch (13 mm) must comply with 405 (Ramps) or 406 (Curb Ramps)....
-
§382.57(c)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
Recommendations
Recommendations Based on the data in Table 1 and the observations above, we recommend: a minimum flat surface of 40 in. length for platforms accommodating wheeled mobility devices...
-
§27.71(k)(6)(i) Input controls.
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
§ 382.57(c)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
§ 27.71(k)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
M301.3 Transfer Supports
Section may be discontinuous (see Rationale) along the length of the Gripping Surface not exceeding 20% of the length of the gripping surface....
-
C1-f
If the slope of part of the accessible route is more than 1:20, does it meet the following requirements for an accessible ramp? Yes No...
-
4.1.3(4)
(4) Interior and exterior stairs connecting levels that are not connected by an elevator, ramp, or other accessible means of vertical access shall comply with 4.9....
-
A4.9.1 Minimum Number
Only interior and exterior stairs connecting levels that are not connected by an elevator, ramp, or other accessible means of vertical access have to comply with 4.9....
-
Element
., telephone, curb ramp, door, drinking fountain, seating, or water closet....
-
ELEMENT
., telephone, curb ramp, door, drinking fountain, seating, water closet....
-
505.5 Clearance
Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum. Figure 505.5 Handrail Clearance...
-
11B-904.4.1 Parallel approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum above the finish floor shall be provided....
-
11B-904.4.1 Parallel approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum above the finish floor shall be provided....