Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, stairs, ramps and landings that are located more than 30 inches (762 mm) measured vertically...
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
1013.2 Where required
-
11B-404.2.3 Clear width
Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the door open 90 degrees....
-
302.2 Carpet
A pile thickness up to ½ inch (13 mm) (measured to the backing, cushion, or pad) is allowed, although a lower pile provides easier wheelchair maneuvering....
-
308.3.2 Obstructed High Reach
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
404.2.3 Clear Width
Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the door open 90 degrees....
-
5.4.2 Transfer Support Length for M301 and M302
This is a linear measurement (see Figure 5.4.1). NPRM Proposed Provision: Length not addressed....
-
Parallel Curb Ramps (R304.3) (Section-by-Section Analysis)
The running slope is measured parallel to the direction of pedestrian travel....
-
302.2 Carpet
A pile thickness up to 1/2 inch (13 mm) (measured to the backing, cushion, or pad) is allowed, although a lower pile provides easier wheelchair maneuvering....
-
Readily Achievable
action; the number of persons employed at the site; the effect on expenses and resources; legitimate safety requirements that are necessary for safe operation, including crime prevention measures...
-
E) Alternate Services
A town should consider the integration requirements of the ADA, which require that priority be given to measures that will provide the service, program, or activity in the most integrated...
-
302.2 Carpet
A pile thickness up to ½ inch (13 mm) (measured to the backing, cushion, or pad) is allowed, although a lower pile provides easier wheelchair maneuvering....
-
308.3.2 Obstructed High Reach
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
4.34.3(2)(b) Reach Depth More Than 10 in
Where the reach depth to the operable parts of any control as measured from the vertical plane perpendicular to the edge of the unobstructed clear floor space at the farthest protrusion...
-
3.3.10 90-Degree Turn
sample was much smaller than the UDI findings (Figure 3‒10), due to differences in the abilities of people or/and WhMD technologies included in each of the studies or due to the different measurement...
-
Clear Floor Space: Minimum Clear Floor Space Required - Manual, Power & Scooter
Dimensions are based on length and width measurements obtained from occupied wheeled mobility devices as part of the Anthropometry of Wheeled Mobility Study....
-
III-4.3100 General
Measures taken to accommodate individuals with other types of disabilities are covered by other title III requirements such as "reasonable modifications" and "alternatives to barrier removal...
-
Data Analyses
Relative oxygen consumption values (ml O2/kg weight/min) measured during the data collection period (stable, plateau phase) were averaged for the resting data and each test surface....
-
Treatment of Data
A bivariate correlation was run to determine any significance between surface deficiencies or non-compliance with the accessibility standards and the measurable results for firmness and...
-
Station 4-Acceleration
Acceleration capabilities were measured for active participants....
-
1015.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
-
General: ADA Standard Section 214.1
Section 214.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for washing machines and clothes dryers.
-
Load and Unload Areas: ADA Standard Section 206.2.9.1
Section 206.2.9.1 covers scoping requirements in the most current ADA Standards for accessible routes to load and unload areas of amusement rides.
-
Height: ADA Standard Section 611.4
Section 611.4 covers the current ADA Standards for the height of the laundry compartment in top loading machines and front loading machines.
-
General: ADA Standard Section 303.1
Section 303.1 of the ADA Standards covers information in the current ADA Standards for changes in level for floor and ground surfaces.