Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
Search Results "Pre-Construction Meeting"
Filters
Commonly Searched Documents
-
404.2.10 Door and Gate Surfaces
-
2. No Admission
The City does not admit any entitlement by Plaintiffs to any relief, or that Plaintiffs have met or can meet the legal standards for a preliminary or permanent injunction, or a declaratory...
-
F) Library Services
In many cases, however, providing basic physical accessibility to the library facility is preferred in meeting the obligation to provide services in the most integrated setting appropriate...
-
DOT Response
parameters of paratransit service, the paratransit agency's policies regarding attended transfers, and the procedures that will be followed in the event that there is no one available to meet...
-
T210 Wheelchair Spaces
A van manufacturer suggested, in response to the 2010 NPRM, that the Access Board add language in the final rule that would allow additional spaces, even if they do not meet the minimum...
-
Emergency Communications [4.10.14]
Emergency two-way communication devices, where provided, must meet the ASME A17.1‒1990 standard....
-
Public Education
shall make a demonstration Edge machine available to the public several months prior to each Election at each of the Supervisor's Offices and by demonstrating it at least twice annually at meetings...
-
Common Requirements (R304.5) (Section-by-Section Analysis)
Surface slopes that meet at grade breaks must be flush. A maximum cross slope of 2 percent is specified for curb ramps, blended transitions, and turning spaces....
-
Carpet [4.5.3]
The trim must meet requirements for changes in level....
-
Product Data and Unit Costs
The data shows that there are a wide variety of examination tables and weight scales available to meet almost every budget....
-
Paragraph (e) (Advisory Guidance)
Although the V.18 standard has been adopted, products are not yet available which meet its requirements. 3....
-
B.
Transportation entities necessarily formulate policies and practices to meet these requirements (e.g., providing fixed route bus service that people with disabilities can use to move among...
-
11B-221.2.1.3 Other boxes
Additionally, because the wheelchair spaces must also meet the dispersion requirements of 221.2.3, the boxes containing these wheelchair spaces cannot all be located in one area unless an...
-
Section 37.31 Vanpools
Public vanpool systems may meet this requirement through obtaining a percentage of accessible vehicles that is reasonable in light of demand for them by participants, but this is not required...
-
Section 37.53 Exception for New York and Philadelphia
On the other hand, alterations begun after January 25, 1992 (including forthcoming key station modifications under the New York and Philadelphia agreements), must meet the requirements of...
-
II-2.1000 General
might loosely characterize these conditions as "disabilities" in relation to the aspirations of the particular individual, the disabilities reached by title II are limited to those that meet...
-
11B-608.2.1 Transfer type shower compartments
permitted in transient lodging guest rooms, multibedroom housing units in undergraduate student housing and residential dwelling units; and shall not be permitted at other locations to meet...
-
11B-221.2.1.3 Other boxes
Additionally, because the wheelchair spaces must also meet the dispersion requirements of Section 11B-221.2.3, the boxes containing these wheelchair spaces cannot all be located in one area...
-
Gamco Recessed Coverall Combination Towel Dispenser and Waste Receptacle - TW-9
All welded construction with exposed surfaces having a #4 satin-finish. One piece seamless door construction, EXTRA HEAVY 18-gauge (1.2mm) with 5/8" (16mm) return for rigidity....
-
4. Exception from the Requirements of M301 for Certain Examination Chairs that Comply with M302
The Access Board proposed in M101.2 in the MDE NPRM to require diagnostic equipment to meet the standards for each patient position supported, meaning that if diagnostic equipment was designed...
-
3.3.1 Research Data
Steinfeld presented their findings at the Committee’s second meeting, and he made himself available to answer Committee and Subcommittee (Examination Tables and Chairs) questions over subsequent...
-
Operable Parts
proposed to require that the operable parts on new automated airport kiosks be tactilely discernible by users to avoid unintentional activation and requested comment regarding the cost of meeting...
-
EXHIBIT A: EDX WEBSITE ACCESSIBILITY POLICY
To meet this goal, edX is implementing several initiatives, including: Conforming www.edx.org, our mobile applications, and our software platform with the Web Content Accessibility...
-
Knee and Toe Clearance (M303.2.4)
requiring in the final standards: a) What would be the incremental costs for the design or redesign and manufacture of the equipment to include toe clearance and knee clearance that meets...
