The directional signs must comply with the requirements of Section 11B-703.5 for visual characters. ◼...
Search Results "Character Spacing (Visual)"
Filters
Commonly Searched Documents
-
11B-207.1 General
-
Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impacts Performance Phase 2: Final Report
Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impact Performance Phase 2: Final Report REPORT PREPARED FOR: U.S ACCESS BOARD, WASHINGTON,...
-
Recreational Boating Facilities
Word Fillable Form (1.6MB) Word Non-Fillable Form (1.5MB) PDF Non-Fillable Form (0.8MB)
-
Lavatory and Accessory Layout by Terry Salo, Architect, CASp
Lavatory and Accessory Layout by Terry Salo, Architect, CASp NOTE: The trash receptacle is preferred to be near the door to allow people to pull the door open with a paper...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
4.30.5* Finish and Contrast
The characters and background of signs shall be eggshell, matte, or other non-glare finish....
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
14. Parking Spaces and Garages
[See subsections ...]
-
Knee and Toe Space Depth
[See subsections ...]
-
Common Questions (Parking Spaces)
Common Questions
-
Sales and Service Elements and Spaces
[See subsections ...]
-
1018.2 Aisles in assembly spaces
[DSA-AC] In addition to the requirements of this section, means of egress, which provide access to, or egress from, buildings or facilities where accessibility is required for...
-
11B-411.2.1.4.1.2 Identification
Buttons shall be identified by raised characters and symbols, white on a black background, complying with Section 11B-703.2 and Braille complying with Section 11B-703.3....
-
Car Controls [4.10.12]
Alignment for a side reach is often difficult at panels on the front of cars due to the limited maneuvering space; consider a maximum height of 48 inches for panels on the front of cars....
-
1018.5 Aisles in other than assembly spaces and Groups B and M
In other than rooms or spaces used for assembly purposes and Group B and M occupancies, the minimum clear aisle capacity shall be determined by Section 1005.1 for the occupant load served...
-
1018.5 Aisles in other than assembly spaces and Groups B and M
In other than rooms or spaces used for assembly purposes and Group B and M occupancies, the minimum clear aisle capacity shall be determined by Section 1005.1 for the occupant load served...
-
Accessible Polling Places for the Visually Impaired: A Compilation of Survey Results
This survey builds upon previous work with the visually disabled population and provides the opinions and recommendations of 202 legally blind voters....
-
4.30.3* COLOR CONTRAST
Characters and symbols shall contrast with their background - either light characters on a dark background or dark characters on a light background....
-
11B-703.8.9 Height above floor
Low resolution VMS characters shall be 40 inches (1016 mm) minimum above the floor of the viewing position, measured to the baseline of the character....
-
Polling places that cannot be remediated with temporary measures:
Parking: Signage for a van accessible parking space is not provided (1991 ADA Stds 4.6.4; 2010 ADA Stds 502.6)....
-
The Impact of Transfer Setup on the Performance of Independent Transfers: Phase I Final Report
The Impact of Transfer Setup on the Performance of Independent Transfers: Final Report REPORT PREPARED FOR: U.S. ACCESS BOARD, WASHINGTON, DC Authors: Alicia Koontz, PhD,...
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Floor Arrival: ADA Standard Section 407.4.8.1.3
Section 407.4.8.1.3 covers the current ADA Standards for visible floor arrival indicators.