36" W x 54" D (91 x 137cm), 1-1/4" (32mm) dia., peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
Search Results "Parallel Grab Bar"
Filters
Commonly Searched Documents
-
Bobrick Two-Wall Tub/Shower Toilet Compartment Grab Bar Peened B-5837.99
-
11B-604.5.2 Rear wall
Where an administrative authority requires flush controls for flush valves to be located in a position that conflicts with the location of the rear grab bar, then the rear grab bar shall...
-
11B-604.5.2 Rear wall
Where an administrative authority requires flush controls for flush valves to be located in a position that conflicts with the location of the rear grab bar, then the rear grab bar shall...
-
609.5 Surface Hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
609.5 Surface Hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
11B-609.5 Surface hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
609.5 Surface Hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
11B-609.5 Surface hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
609.5 Surface Hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
11B-609.5 Surface hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
Figure 604.5.1 Side Wall Grab Bar at Water Closets – Drawing from the U.S. Access Board
-
Figure 609.3 Spacing of Grab Bars – Drawing from the U.S. Access Board
-
609.2 Cross Section
Grab bars shall have a cross section complying with 609.2.1 or 609.2.2....
-
609.2 Cross Section
Grab bars shall have a cross section complying with 609.2.1 or 609.2.2....
-
609.2 Cross Section
Grab bars shall have a cross section complying with 609.2.1 or 609.2.2....
-
11B-609.2 Cross section
Grab bars shall have a cross section complying with Section 11B-609.2.1 or 11B-609.2.2....
-
609.2 Cross Section
Grab bars shall have a cross section complying with 609.2.1 or 609.2.2....
-
11B-609.2 Cross section
Grab bars shall have a cross section complying with Section 11B-609.2.1 or 11B-609.2.2....
-
11B-609.2 Cross section
Grab bars shall have a cross section complying with Section 11B-609.2.1 or 11B-609.2.2....
-
Figure 1009.5.7 Grab Bars – Drawing from the U.S. Access Board
-
Gamco Swing Up Grab Bar - 125-Swing-Up
Detent holds bar in vertical position. Back Plate - 3/16" (4.5mm) thick, one piece stainless steel design....
-
11B-609.8 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device,...
-
609.8 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device,...
-
609.8 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device,...
