Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
Search Results "ANSI/HFES: American National Standards Institute/ Human Factors and Ergonomics Society"
Filters
Commonly Searched Documents
-
Receiver Jacks: ADA Standard Section 706.2
-
11B-706.2 Receiver jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
How to Use the ADA 2010 Standards Electronic Pocket Guide
-
Chapter 7: Referenced Standards
[See subsections ...]
-
E102.7 International Telecommunications Union Telecommunications Standardization Sector (ITU-T)
Copies of the referenced standards may be obtained from the International Telecommunication Union, Telecommunications Standardization Sector, Place des Nations CH-1211, Geneva 20, Switzerland...
-
The Roles of the Access Board and the Department of Justice
The ADA requires the Department to issue regulations that include enforceable accessibility standards applicable to facilities subject to title II or title III that are consistent with the...
-
APPENDIX A: Federal Trail Data Standards (FTDS) – Trail Fundamentals
11/08/2011 Trail Type ◼ Trail Class ◼ Managed Use ◼ Designed Use The Federal Trail Fundamentals include four concepts that are the cornerstones of effective trail...
-
23. Q: We are going to build a new facility. What architectural standards do we have to follow to make sure that our facility is accessible to people with disabilities?
What architectural standards do we have to follow to make sure that our facility is accessible to people with disabilities?...
-
ADA Overview
[See subsections ...]
-
The Disability Community
The Disability Community Within a few weeks the ADA will become the law of the land because of the vision of the disability community. You knew in your hearts what we now write...
-
Section 35.151(c) Accessibility Standards for New Construction and Alterations (Section-by-Section Analysis)
Section 35.151(c) proposes to adopt Parts I and III of the Americans with Disabilities Act and Architectural Barriers Act Guidelines, 69 FR 44084 (July 23, 2004) (2004 ADAAG) as the ADA...
-
2. Effective Date
On March 15, 2012, compliance with the 2010 Standards will be required for new construction and alterations....
-
2 - Specifications
If specific tolerances or requirements are not stated in the specifications (or drawings) it is generally held by the courts that industry standards apply....
-
Handbook of Construction Tolerances by David Kent Ballast FAIA, CSI
Updating and expanding on its popular first edition, the Handbook of Construction Tolerances, Second Edition remains the only comprehensive reference to the thousands of industry standard...
-
CHAMPIONS OF CHANGE: 23rd Anniversary of the Americans with Disabilities Act
Requires the Registered User plan or above. Login!
-
§ 35.151(c) Accessibility standards and compliance date.
(c) Accessibility standards and compliance date....
-
APPENDIX B: Federal Trail Data Standards – Class Matrix
The Trail Class identified for a trail prescribes its development scale, representing its intended design and management standards.1 Local deviations from any Trail Class descriptor may...
-
1630.15(b)(2)
(2) Direct threat as a qualification standard....
-
Which accessibility guidelines must we use?
The new combined guidelines replace both the Uniform Federal Accessibility Standards (UFAS) and the Americans with Disabilities Act Accessibility Guidelines (ADAAG)....
-
‘‘Act.’’ (Preamble, Section-by-Section Analysis)
The word ‘‘Act’’ is used in the regulation to refer to the Americans with Disabilities Act of 1990, Pub. L. 101–336, which is also referred to as the ‘‘ADA.’’...
-
E. What are the General Requirements for Curb Ramps in the ADA Standards for Accessible Design?
One way to make curb ramps compliant with Title II of the ADA is to build them in accordance with the ADA Standards. 7 Following are the key characteristics of an accessible curb ramp according...
-
3.2 Dimensional Tolerances
All dimensions are subject to conventional building industry tolerances for field conditions.
-
3.2 DIMENSIONAL TOLERANCES
All dimensions are subject to conventional building industry tolerances for field conditions.
-
4.1.7(2)(d) Certified Local Government Historic Preservation Programs
delegated the consultation responsibility for purposes of this section to a local government historic preservation program that has been certified in accordance with section 101(c) of the National...
