Single, multi or C-fold towels 12 gallon waste capacity Model 237 - Recessed Model 237-10 - Semi-recessed (recesses 3-1/2"; projects 4") Model 237-11 - Surface...
Search Results "Composite Rubber Surface"
Commonly Searched Documents
- Bradley High Capacity Towel Dispenser / 12 Gallon Waste 237
- Bradley 12 Gallon Waste Receptacle 344
- Bradley Low Capacity Towel Dispenser / 1.25 Gallon Waste Receptacle 229
- Bradley Low Capacity Towel Dispenser 2442
- Bradley High Capacity Towel Dispenser / 8.2 Gallon Waste 238
-
B. What Is a Curb Ramp?
The gutter is the roadway surface immediately next to the curb ramp that runs along the curb. 1 28 C.F.R. Part 36, Appendix A, § 3.4....
-
1008.2.3 Water Play Components
Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6...
-
Chapter 3: Building Blocks
These requirements address floor and ground surfaces (302), changes in level (303), wheelchair turning space (304), clear floor or ground space (305), knee and toe clearance (306), protruding...
-
R204.2 Pedestrian Circulation Paths
The NPRM proposed to define a pedestrian circulation path as a prepared exterior or interior surface provided for pedestrian travel in the public right-of-way. See R105.5....
-
308.3.2 Obstructed High Reach
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
809.2 Residential Dwelling Units with Mobility Features
809.2 Residential Dwelling Units with Mobility Features As discussed below, the final rule adds technical requirements to this section for floor surfaces, bedrooms, and weather alert...
-
1008.2.3 Water Play Components
Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6...
-
Spy City Café
The bottom edges of the reflecting surfaces of the mirrors in the men's and women's toilet rooms located outside the Café and designated as accessible are mounted 57 ½" [sic] from the finished...
-
M301.3.3 Head and Back Support
This is consistent with ANSI/AAMI HE 75 which recommends that the “support surface needs to be adjustable or have adjustable features (e.g., for the head, neck, back, lumbar region, leg,...
-
604.7 Dispensers
paper dispensers are installed above the side wall grab bar, the outlet of the toilet paper dispenser must be 48 inches (1220 mm) maximum above the finish floor and the top of the gripping surface...
-
1008.2.3 Water Play Components
Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6...
-
B) Accessible Route
be at least 36 inches wide, have no abrupt vertical changes in level (such as a step), have a running slope no more than 1:12 in most cases, and meet other requirements for cross slope, surface...
-
Parking Spaces [4.6.3]
A maximum slope of 2% is required in all directions for both the space and access aisle since level surfaces are important for wheelchair transfer to and from vehicles....
-
308.3.2 Obstructed High Reach
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
308.3.2 Obstructed High Reach
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
Location [§208.3]
Locating accessible spaces required for a parking structure in a surface lot often will not qualify for this exception because such a location typically offers less convenience, security...
-
Slope [§405.2] and Cross Slope [§405.3]
will accommodate most irregularities or variances due to construction methods or materials according to a study sponsored by the Board (“Dimensional Tolerances in Construction and for Surface...
-
Some existing measurement protocols
Some existing measurement protocols Currently there are no generally accepted measurement protocols for determining the slope, flatness, or waviness of floor surfaces in terms of accessibility...
-
Changes in Level at Entry to Wheelchair Spaces (M303.3)
with drop offs ½ inch or greater would be required to provide edge protection 2 inches high minimum on each side to prevent users from inadvertently travelling off the sides of the ramped surface...