The FF defines the maximum floor curvature ed over a 24 - inch (600 mm) length computed on the basis of successive 12 - inch (300 mm) elevation differentials....
Search Results "Expected Maximum Flight Duration"
Filters
Commonly Searched Documents
-
F - number system
-
11B-232.1 General
alterations are originally planned), provided that each substitute cell— (i) Is located within the same prison site; (ii) Is integrated with other cells to the maximum...
-
II-6.5000 Alterations to historic properties
Alterations to historic properties must comply with the specific provisions governing historic properties in ADAAG or UFAS, to the maximum extent feasible....
-
II-3.3000 Equality in participation/benefits
The major principles of mainstreaming are -- 1) Individuals with disabilities must be integrated to the maximum extent appropriate. 2) Separate programs are permitted where necessary...
-
DOT Response
., to use a walker, even one with a seat intended to allow temporary rest intervals, as a wheelchair in which a passenger sits for the duration of a ride on a transit vehicle)....
-
Public Elementary and Secondary Schools
Ensure that students with disabilities are educated with students without disabilities to the maximum extent appropriate....
-
Final Regulatory Flexibility Analysis
Determining whether such an element exists is expected to take only a minimal amount of staff time....
-
Wheelchair Fitness Solution™ Complete Fitness System
The patented harness anchors you to the ramp for maximum resistance and a complete gym quality workout....
-
Subpart F—Certification of State Labs or Local Building Codes (Preamble, Section-by-Section Analysis)
In fact, the Department expects that in some cases, rather than certifying portions of a particular code and refusing to certify others, it may notify a submitting jurisdiction of deficiencies...
-
Ticket Agent Web sites
ASTA specifically supported this proposal as a viable trade-off for small entities in lieu of Web site conformance, saying that such businesses expect to have personal interaction with consumers...
-
Subpart F—Certification of State Labs or Local Building Codes (Section-By-Section Analysis and Response to Comments)
In fact, the Department expects that in some cases, rather than certifying portions of a particular code and refusing to certify others, it may notify a submitting jurisdiction of deficiencies...
-
6. Recognize that Proper Installation of Play Surface Systems is Key
Site plans and construction drawings should provide details like maximum running slopes and cross slopes, beveled edges, transitions, adjoining seams and affixing the surface material to...
-
1011.2.1 Size and Location
recreation access route or trail, as applicable, or another clear ground space Locate the space so that the water spout is 11 inches (280 mm) minimum and 12 inches (305 mm) maximum...
-
Volume Control
The ANSI A117.1 standard requires certain public pay telephones to provide 12 decibels of gain minimum and up to 20 decibels maximum and that an automatic reset be provided....
-
Accessible Route
For example, where the total length of a gangway or series of gangways serving as an accessible route is 80 feet or more an exception permits the slope on gangways to exceed the maximum...
-
M102.1 Defined Terms (Section-by-Section Analysis)
defined: health care provider, breast platform, patient support surface, transfer supports, positioning supports, prone position, supine position, examination tables, diagnostic purposes, maximum...
-
(1) Adjustability: Minimum High Transfer Height
Therefore, transfer surfaces that are adjustable to a 25-inch maximum during patient transfer accommodate most patients who use mobility devices....
-
M303.2.4 Equipment Clearances (Section-by-Section Analysis)
to clarify that the measurement is taken from the toe end of the wheelchair space. 10 The Wheeled Mobility Anthropometry Project recommended a toe clearance that is 5 inches deep maximum...
-
(C) NYCT’s interpretation of the ADA and DOT’s implementing regulations is too narrow.
facility,” for the reasons set forth above, DOT’s regulations (specifically, 49 CFR § 37.43(a)(1)) expressly require that the public entity shall make the alteration “in such a manner, to the maximum...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The width of the base permitted within this clearance would be 26 inches maximum at the edge of the examination surface and was permitted to increase at a rate of 1 inch in width for every...
-
Clear Ground Space [1011.2]
Locate the clear space so that the water spout is a minimum of 11 inches and a maximum of 12 inches from the rear center of the long side of the space....
-
Roundabouts (Section-by-Section Analysis)
Where chains, fencing, or railings are used for edge protection, the bottom edge of the treatment must be 380 millimeters (15 inches) maximum above the sidewalk to be detectable by cane....
-
A) Accessible Parking
Access aisle of at least 60-inch width must be level (1:50 maximum slope in all directions), be the same length as the adjacent parking space(s) it serves and must connect to an accessible...
-
Table 2: Summary of Department of Transportation Survey
Element surveyed Minimum reported tolerance Maximum reported tolerance Average reported tolerance Final suggested tolerance 1 Roadway grade...
