Search Results "Door Surface"
Filters
Commonly Searched Documents
-
Figure 404.2.4.1(h) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Pull Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(j) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Push Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(d) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Pull Side – Drawing from the U.S. Access Board
-
M301.2.2 Size
The transfer surface shall be 30 inches (760 mm) wide minimum and 15 inches (381mm) deep minimum. Advisory M301.2.2 Size....
-
SDC Sure Exit® PSB560 REX Pressure Sense Exit Bar
Stable and Reliable Pressure Sense Technology Building codes essentially state that egress through access controlled doors must not require prior knowledge of operational requirements...
-
Sargent 8500 Narrow Design Rim Exit Device
Features Designed for narrow stile applications such as aluminum frame full glass doors Single and double doors with mullion Single point rim latching device...
-
Allegion Falcon 25 Series Touch Bar Exit Devices
Offices, banks, assisted living facilities, retail stores and other commercial buildings have constant traffic, so door hardware must be able to take continual use and abuse....
-
Sargent 8888 Reversible Rim Exit Device
The 8888 is designed for standard width stile applications on wood and metal doors and has 7 functions determined by the trim function....
-
HEWI Panic Bar EN 1125
Special solutions for exit doors must enable fast escape in an emergency....
-
7(2)(a)
(a) Bathrooms that have reinforced walls for grab bars (see Requirement 6) would meet section 100.205(c)(3)(iv) if: Note: Cabinets under lavatories are acceptable provided the...
-
§100.205(c)
(c) All covered multifamily dwellings for first occupancy after March 13, 1991 with a building entrance on an accessible route shall be designed and constructed in such a manner that—
-
Surface
Surface The surface of the transfer platform and steps must not be sharp and must have rounded edges to prevent injuries....
-
Figure 404.2.4.1(i) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Pull Side with Closer – Drawing from the U.S. Access Board
-
TownSteel TRXL Grade 1 Cylindrical Lock with Ligature Resistant Trim
It fits standard 161 door prep....
-
Corbin Russwin Inc. ED5000 Series Exit Device
Aesthetics Over the past 100 years, Corbin Russwin has been well-known for weaving pleasing aesthetics and inventive designs into architectural door hardware, and today’s wide stile exit...
-
Behavioral Safety Products #DH410 Cylindrical Ligature Resistant Lever Handle
The escutcheon plate is sloped at a low profile, from the door to the lever handle itself, to eliminate any further ligature points, and maintains extremely tight tolerances. ...
-
Allegion Falcon 1990 Series Cross Bar Exit Devices
: Hex dogging standard Cylinder: Rim, key entry (NL) or hold back (HB) available (field selectable) Sizes: Field adjustable width, 41" crossbar standard fits 3' 8" x 7' door...
-
Figure 404.2.4.1(g) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Push Side with Closer and Latch – Drawing from the U.S. Access Board
-
Allegion Von Duprin 33A/35A Series Exit Devices
33A and 35A for all types of single and double doors with mullion, UL listed for Panic Exit Hardware. Devices are ANSI A156.3 – 2001 Grade 1....
-
Surface
Surface Since people using transfer walls are in bathing suits, their skin may be in contact with the wall....
-
M301.2.4 Unobstructed Transfer
Each transfer surface shall provide two unobstructed sides for patient transfer. EXCEPTIONS: 1....
-
M301.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
Allegion Von Duprin 55 Series Cross Bar Exit Devices
5575 mortise lock devices for all types of single and double doors. UL listed for accident hazard installations....
