Mirrors: If provided, mirrors need to be mounted with the bottom edge of the reflecting surface no higher than 40 inches above the floor....
Search Results "Work Surface"
-
2. Mirrors
-
705.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705. Figure 705.1 Size and Spacing of Truncated Domes...
-
5.4.3.1 Positioning Support Height for Imaging Equipment
Positioning supports should be positioned 3 to 6 inches above the transfer surface....
-
R305.2.6 Boarding Platforms
At boarding platforms for buses and rail vehicles, detectable warning surfaces shall be placed at the boarding edge of the platform....
-
e-i
Is the curb ramp surface at least 36 inches wide, excluding flared sides? [ADA Standards § 4.7.3] Yes No...
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2....
-
RAMP
A walking surface that has a running slope steeper than one unit vertical in 20 units horizontal (5-percent slope)....
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2. ...
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2....
-
RAMP
A walking surface that has a running slope steeper than one unit vertical in 20 units horizontal (5-percent slope)....
-
Boat Launch Ramp
A sloped surface designed for launching and retrieving trailered boats and other water craft to and from a body of water....
-
Maintenance and Back-Up
The ADA regulation contains a specific provision requiring that covered entities maintain their accessibility features and equipment in operable working condition....
-
Applicability
approval of the appropriate GSA Assistant Regional Administrator, Public Buildings Service, where such specific authorization may facilitate improvements in the efficiency in performing work...
-
Executive Summary
Much of the Committee work occurred within five Subcommittees that addressed major categories of MDE: Examination Tables and Chairs; Stretchers; Diagnostic Imaging Equipment; Mammography...
-
11B-224.7.2 Multi-bedroom housing units with adaptable features
sleeping rooms) or on floors containing accessible sleeping rooms with mobility features shall provide turning spaces that comply with section 809.2.2 of the 2010 Standards and kitchen work...
-
Paragraph (h) Non-interference with hearing technologies (Section-by-Section Analysis)
They urged the Board to defer any such requirement until the ANSI C63 Committee had finished its work....
-
Section 1630.14(b) Employment Entrance Examination
Section 1630.14(b) Employment Entrance Examination An employer is permitted to require post-offer medical examinations before the employee actually starts working....
-
Emergency Evacuation Preparedness: Take Responsibility for Your Safety
Ray, who has quadriplegia and works on the second floor, said it was the first fire drill in the 18 months he's worked there....
-
Issue 15: Installation Errors Increase Risk
When you press the button, the light comes on to let you know that it’s working. When the WALK signal begins, you hear a fast ticking sound”....
-
11B-405.9.2 Curb or barrier
or barrier shall be provided that prevents the passage of a 4 inch (102 mm) diameter sphere, where any portion of the sphere is within 4 inches (102 mm) of the finish floor or ground surface...
-
Openings [1016.6]
Openings are gaps in the surface of an ORAR....
-
4.26.2* SIZE AND SPACING OF GRAB BARS AND HANDRAILS
The diameter or width of the gripping surfaces of a handrail or grab bar shall be 1-1/4 in to 1-1/2 in (32 mm to 38 mm), or the shape shall provide an equivalent gripping surface....
-
4.35.4 Bench
Where installed in conjunction with showers, swimming pools, or other wet locations, water shall not accumulate upon the surface of the bench and the bench shall have a slip-resistant surface...
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...