Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger drop-off and loading zone and from the passenger drop-off and loading zone to...
Search Results "Clear Floor Space"
Filters
Commonly Searched Documents
-
11B-503.5 Vertical clearance
-
Section 36.406(f) Assembly Areas (Section-by-Section Analysis)
As the Department explained in the NPRM, however, this provision was not designed to prohibit temporary seating that increases seating for events (e.g., placing temporary seating on the floor...
-
11B-233.3.1.2.6 Public housing facility site impracticality
The remaining ground floor residential dwelling units shall comply with the following requirements: 1. Grab bar reinforcement complying with Section 11B-609. 2. ...
-
M-D Building Products, Inc. GEN3 SmartTool™ Digital Level
cover design Larger buttons for gloved fingers Easy-to-read buttons Recessed mode button to prevent accidental changes More rugged – drop tested to over 3 feet onto concrete floor...
-
A. ACCESSIBLE SEATING
space requirements set forth in table 221.2.1.1 of the Standards....
-
Guidelines for Requirement 4
The Department has adopted the Option One guidelines for Requirement 4 with the following changes: First, the Department has eliminated the specification for maneuvering space if a person...
-
AXS Map App - Find, Rate and Share Accessible Places
Amazingly simple to use. On web and mobile. Created by Jason DaSilva and the AXS Lab team. Find Use our app or web site to find accessible places in your area. Browse for...
-
3. Exception to Ramp Running Slope
The MDE Advisory Committee, during its discussion of wheelchair spaces on weight scales, extensively addressed the permissible slopes of ramps on raised platforms....
-
11B-609.3 Spacing
The space between the wall and the grab bar shall be 1½ inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
Ticketing (Assembly areas, not parking.)
Title II Regulations 28 § 35.138 Ticketing: (a) (1) For the purposes of this section, “accessible seating” is defined as wheelchair spaces and companion seats that comply with...
-
M303.1 General
Diagnostic equipment used by patients seated in a wheelchair shall comply with M303.
-
M303.3.1 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical.
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2.
-
M303.4 Components
Where components of diagnostic equipment are used to examine specific body parts, the components shall be capable of examining the body parts of a patient seated in a wheelchair....
-
F202.6.5.5 Assembly Areas
Assistive listening systems shall comply with F219 and assembly seating shall comply with F221.
-
M303.4 Components (Section-by-Section Analysis)
The MDE NPRM proposed to require diagnostic equipment used by patients seated in a wheelchair which has components that are used to examine specific body parts, be capable of...
-
M303.1 General (Section-by-Section Analysis)
This is an introductory section.
-
Key Features of Accessible Stadiums
[See subsections ...]
-
T208 Passenger Access Routes
[See subsections ...]
-
T605 Seat Belts and Shoulder Belts
[See subsections ...]
-
A2
A2. Is the vehicle pull-up area relatively level (1:50 or 2% maximum slope in all directions)? Yes No
-
A4.8.2 Slope and Rise
Ramp slopes between 1:16 and 1:20 are preferred. The ability to manage an incline is related to both its slope and its length. Wheelchair users with disabilities affecting their arms...
-
A4.8.2 SLOPE AND RISE
The ability to manage an incline is related to both its slope and its length. Wheelchair users with disabilities affecting arms or with low stamina have serious difficulty using...
-
M303.4 Components
Where components of diagnostic equipment are used to examine specific body parts, the components shall be capable of examining the body parts of a patient seated in a wheelchair....
