A police department may create a specific class of light duty jobs that are limited to incumbent police officers....
Search Results "Specification"
-
18. Q: May a police department create a light duty job category reserved only for incumbent officers without offering identical positions to job applicants?
-
11B-411.2.1.2.4 Display screen
Amends requirements so that operating instructions are specific to the building....
-
11B-411.2.1.2.5 Audio output
Amends requirements so that operating instructions are specific to the building....
-
§ 382.57(a)(5)
(5) You must ensure that each automated airport kiosk that meets the design specifications in paragraph (c) of this section is:...
-
4.26.3 Structural Strength
The structural strength of grab bars, tub and shower seats, fasteners, and mounting devices shall meet the following specification:...
-
Is a center handrail required at wide stairways?
If a center handrail is provided, compliance with the handrail specifications, while advisable, is not required....
-
CHILDREN’S USE
[DSA-AC] Describes spaces and elements specifically designed for use primarily by people 12 years old and younger....
-
§ 35.136(i)(2)(iv)
(iv) Whether the miniature horse's presence in a specific facility compromises legitimate safety requirements that are necessary for safe operation....
-
§ 37.73(c)(2)
(2) A nationwide search for accessible vehicles, involving specific inquiries to used vehicle dealers and other transit providers; and...
-
§ 37.87(c)(2)
(2) A nationwide search for accessible vehicles, involving specific inquiries to used vehicle dealers and other transit providers; and...
-
CHILDREN’S USE
[DSA-AC] Describes spaces and elements specifically designed for use primarily by people 12 years old and younger....
-
Children's Use
Describes spaces and elements specifically designed for use primarily by people 12 years old and younger....
-
Keypad Buttons
expressed for making this requirement consistent with the ANSI A117.1‒1998 standard which requires a standard keypad arrangement with a raised dot on the number 5 key which is held to specifications...
-
T-turn Maneuvering Space
Several commenters stated that this design specification was unclear in two respects....
-
Water Flow Height
A comment noted that the rationale for this specification is not needed in the text of the requirement and might be misinterpreted as allowing cup dispensers as an alternative to accessible...
-
220 and 707 Automatic Teller Machines and Fare Machines
220 and 707 Automatic Teller Machines and Fare Machines Section 707 of the 2010 Standards adds specific technical requirements for speech output, privacy, tactilely-discernible input...
-
17.1 Q. Is it correct that only the exterior side of the main entry door of covered multifamily dwellings must meet the ANSI requirements?
The exterior side of the main entry door is part of the public and common use areas and therefore must meet ANSI A117.1 1986 specifications for doors....
-
§104.44(a) Academic requirements
Modifications may include changes in the length of time permitted for the completion of degree requirements, substitution of specific courses required for the completion of degree requirements...
-
2.3.1 Standards
2.3.1 Standards There are no standards that we are aware of that specifically cover the unique aspects of IR systems....
-
1005 Fishing Piers and Platforms
Specifications for fishing piers and platforms address accessible routes, railings, edge protection, clear floor space, and turning space....
-
§382.13(b)
(b) This requirement is part of your general nondiscrimination obligation, and is in addition to your duty to make the specific accommodations required by this part....
-
1008 Play Areas
The play area specifications address accessible routes, ground level and elevated play components, play structures, and ground surfaces....
-
11B-104.3 Figures
Unless specifically stated otherwise, figures are provided for informational purposes only. FIGURE 11B-104 GRAPHIC CONVENTION FOR FIGURES...
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....