Handrails shall be provided on both sides of stairs and ramps....
Search Results "Handrail Diameter"
Filters
Commonly Searched Documents
-
505.2 Where Required
-
§ 38.77(b)
the vehicle while starting to board, and to continue using such handrails or stanchions throughout the boarding process....
-
Handrails [ADA Standards §504.6, §505]
Handrails [ADA Standards §504.6, §505] Specifications in the ADA Standards for handrail surfaces and clearances facilitate a power grip along the handrail length....
-
Clearances between a handrail and wall surface: 2012 NFPA 101 vs. 2010 ADA
Question/Issue: According to the new 2012 NFPA 101 Life Safety Code, Chapter 7, Section 7.2.2.4.4.5 & Exhibit 7.97, the finger clearance at an existing stair handrail should be...
-
1008.2.5.3.1 Handrail Gripping Surfaces
1008.2.5.3.1 Handrail Gripping Surfaces....
-
Aisle Stairs and Ramps in Assembly Areas
Sections 505.2 and 505.3 of the 2010 Standards provide exceptions for aisle ramp handrails....
-
Figure 505.6 Horizontal Projections Below Gripping Surface – Drawing from the U.S. Access Board
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
Can stair handrail extensions overlap door maneuvering clearances?
No, handrails and other elements cannot overlap door maneuvering clearances....
-
R409.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
T207.1 General
Non-rail vehicles shall provide handrails, stanchions, and handholds in accordance with T207. Handrails, stanchions, and handholds shall comply with T303....
-
Section 4.26.4
• Section 4.26.4 of the 1991 Standards requires handrail gripping surfaces to have edges with a minimum radius of 1/8 inch....
-
Can handrails overlap door maneuvering clearances?
door maneuvering clearances can be offset up to 8” from the face of the door or gate to accommodate wall thickness, casework, shelves, or other elements adjacent to doorways, including handrails...
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
T303.4 Clearance
Clearance between gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum.
-
Ramps
Provide handrails on each side of the ramps at the following locations:...
-
Extremely well done!
Hello Corada, Thank you ETA and Dan for pointing me to this How-to video on measuring handrail extensions....
-
A4.26.1 General
Many disabled people rely heavily upon grab bars and handrails to maintain balance and prevent serious falls....
-
A4.26.1 GENERAL
Many disabled people rely heavily upon grab bars and handrails to maintain balance and prevent serious falls....
-
4.9.4(3)
(3) The clear space between handrails and wall shall be 1‒1/2 in (38 mm)....
