On blended transitions, detectable warning surfaces shall be placed at the back of curb....
Search Results "Surface Slope"
-
R305.2.3 Blended Transitions
-
3. Medical Diagnostic Equipment
rulemaking (NPRM) to remove the sunset provisions in the our existing accessibility standards for medical diagnostic equipment (MDE) related to the low-height specifications for transfer surfaces...
-
3. Medical Diagnostic Equipment
rulemaking (NPRM) to remove the sunset provisions in the our existing accessibility standards for medical diagnostic equipment (MDE) related to the low-height specifications for transfer surfaces...
-
Chapter 9: Built-In Elements
Chapter 9 covers built-in elements, including dining surfaces and work surfaces (902), benches (903), and sales and service counters (904)....
-
Acknowledgments
Acknowledgments The development of objective surface measurement devices and objective surface testing was conducted with funding from the National Center for Medical Rehabilitation Research...
-
Using the Polling Place Checklist
Using the Polling Place Checklist Tools and Documentation A few simple tools may be used to measure the sizes and the slope of specific elements and spaces: • A metal tape measure...
-
Exterior Features
Sidewalks not exceeding a 5% slope (with a 2% side slope) Passenger loading zone with zero clearance exterior route for people using mobility devices....
-
1010.1.7 Thresholds
Raised thresholds and floor level changes greater than ¼ inch (6.4 mm) at doorways shall be beveled with a slope not greater than one unit vertical in two units horizontal (50-percent slope...
-
11B-705.2 Detectable directional texture
transit boarding platforms shall comply with Figure 11B-705.2 and shall be 0.1 inch (2.5 mm) in height that tapers off to 0.04 inch (1.0 mm) , with bars raised 0.2 inch (5.1 mm) from the surface...
-
Gratings [4.5.4]
These requirements apply to gratings located in any walking surface, including courtyards and plazas, not just those on accessible routes....
-
11B-705.2 Detectable directional texture
transit boarding platforms shall comply with Figure 11B-705.2 and shall be 0.1 inch (2.5 mm) in height that tapers off to 0.04 inch (1.0 mm) , with bars raised 0.2 inch (5.1 mm) from the surface...
-
1133A.4.1 Repositionable countertops
Repositionable countertops shall comply with the following: Sinks and work surfaces required by Section 1133A.4 shall be designed to enable repositioning to a minimum height of 28...
-
Gangways
Gangways A gangway is a variable-sloped pedestrian walkway linking a fixed structure or land with a floating structure....
-
11B-403.7 Continuous gradient
The slope of the resting area in all directions shall be 1:48 maximum. ETA Editor's Note 2013 CBC requirement 11B-403.7 is not present in 2010 ADAS. ...
-
Clearance
Section 403.5 specifies a continuous clearance of 36 inches minimum for walking surfaces....
-
M307.2 Tactilely Discernible (Section-by-Section Analysis)
Patients who are blind or have low vision have difficulty distinguishing a flat membrane button or similar control unless it is tactilely discernible from the surrounding surface and any...
-
904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
-
4.34.6.4(1)
(1) The counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable or replaceable as...
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
3.2 Study Limitations and Other Issues
warning surface and the luminance contrast of the warning surface with adjacent surfaces....
-
R208.1 Where Required
Detectable warning surfaces complying with R305 shall be provided at the following locations on pedestrian access routes and at transit stops: 1....
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
-
Seat Height
Commenters noted that this specification should be clarified as applying to the height as measured at the top of the seat surface. Response....
-
11B-904.3.2 Counter
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....