[DSA-AC] The clear height of vehicle and pedestrian areas required to be accessible shall comply with Chapter 11A or 11B, as applicable. Advisory 406.4.1 Clear height....
Search Results "Local Requirement"
Filters
Commonly Searched Documents
-
406.4.1 Clear height
-
11B-407.4.10 Support rail
Support rails in elevator cabs are required to comply with the requirements of this section, not the requirements for handrails on walking surfaces. ◼ ETA Editor's Note There is no...
-
11B-203.7 Detention and correctional facilities
In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required...
-
11B-203.7 Detention and correctional facilities
In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required...
-
11B-203.7 Detention and correctional facilities
In detention and correctional facilities, common use areas that are used only by inmates or detainees and security personnel and that do not serve holding cells or housing cells required...
-
11B-206.2.4 Spaces and elements
In assembly areas with fixed seating required to comply with Section 11B-221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an...
-
2 - Specifications
Specifications allow the requirements to be stated as succinctly or as elaborately as required....
-
11B-206.2.4 Spaces and elements
In assembly areas with fixed seating required to comply with Section 11B-221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an...
-
11B-206.2.4 Spaces and elements
In assembly areas with fixed seating required to comply with Section 11B-221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an...
-
232.1 General
Notwithstanding the requirements of this section, section 201.1.1 shall apply. Advisory 232.1 General....
-
M301.1 General (Section-by-Section Analysis)
The MDE NPRM proposed that all diagnostic equipment used by patients in a supine, prone, or side-lying position must comply with the technical requirements of proposed section M301....
-
402.2.2 Braille Instructions (Section-by-Section Analysis)
Braille instructions would be required to conform to specifications for braille in the ADA and ABA Accessibility Guidelines....
-
Steps to Minimize Significant Economic Impacts on Small Entities
The final rules permits exceptions to the specific provisions in the technical requirements for certain elements and facilities based on the conditions listed in Table 2 under Executive...
-
11B-217.4 TTYs
Separate requirements are provided based on the number of public pay telephones provided at a bank of telephones, within a floor, a building, or on a site....
-
11B-217.4 TTYs
Separate requirements are provided based on the number of public pay telephones provided at a bank of telephones, within a floor, a building, or on a site....
-
11B-233.3.1.2 Residential dwelling units with adaptable features
The requirements in this section were previously found in Chapter 11A. Please see section 1150A.1 for the 2019 Chapter 11A language....
-
11B-604.5.2 Rear wall
Where an administrative authority requires flush controls for flush valves to be located in a position that conflicts with the location of the rear grab bar, then the rear grab bar shall...
-
Altered Elements on an Accessible Route
A second exception notes that compliance is required unless it is technically infeasible, in which case compliance is required to the maximum extent feasible (202.3, Exception 2)....
-
Just Manufacturing 42" Stainless Steel Grab Bar
concealed screws Brushed stainless finish Grab bar to wall distance 1-1/2" ADA Compliant Product: JGRB-42 Product Note: Grab bars meet or exceed A.D.A. requirement...
-
Just Manufacturing 24" Stainless Steel Grab Bar
requirement of 250 lbs. when properly installed. A grab bar is only as strong as the anchoring devices and the wall on which it is mounted....
-
Just Manufacturing 36" Stainless Steel Grab Bar
concealed screws Brushed stainless finish Grab bar to wall distance 1-1/2" ADA Compliant Product: JGRB-36 Product Note: Grab bars meet or exceed A.D.A. requirement...
-
Just Manufacturing 30" Stainless Steel Grab Bar
concealed screws Brushed stainless finish Grab bar to wall distance 1-1/2" ADA Compliant Product: JGRB-30 Product Note: Grab bars meet or exceed A.D.A. requirement...
-
Mansfield Urinal Suburban Commercial 475
.-2008/CSA B45.1-08 Complies with ADA requirements for accessibility...
-
Seton California Code ADA Men Rest Room Sign with Larger ISA - Black
Signs specifically meet the requirements of California's Uniform Building Code The Men's Rest Room sign is constructed of an equilateral triangle 1/4" thick with edges 12" long and...
