Where mirrors are provided the bottom edge of the reflective surface shall be 40 inches (1016 mm) maximum above the finish floor....
Search Results "Composite Rubber Surface"
-
11B-809.10.8.7 Mirrors and towel bars
-
11B-403.5 Clearances
Walking surfaces shall provide clearances complying with Section 11B-403.5....
-
403.5 Clearances
Walking surfaces shall provide clearances complying with 403.5....
-
III-4.3600 Limitations and alternatives
number of its employees; the number, type, and location of its facilities; and 5) If applicable, the type of operation or operations of any parent corporation or entity, including the composition...
-
Panda S.90 All Aluminum Slim Profile Multi-Slide Door System
Accessories Wheels are made from nylon reinforced synthetic composite material for quiet operation with encased stainless steel ball bearings....
-
11B-1009.5.7 Grab bars
Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (102 mm) minimum and 6 inches (152 mm) maximum above each step and transfer platform....
-
11B-705.1.1.2 Dome spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
Backrests
Backrests: The backrest design for platform 1, the first surface that participants transferred to from their WMD as seen in Table 2, was based on bench seat back supports in section 903.5...
-
11B-606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (864 mm) maximum above the finish floor or ground....
-
1017.5 Tread Obstacles
The vertical alignment of joints in concrete, asphalt, or board surfaces on trails can be tread obstacles....
-
Instrumentation for Analysis
Upon installation, the playground owner completed a questionnaire (Appendix B) on the type, size and intended age group of the playground, the total cost for the equipment, surface materials...
-
Additional Technical Criteria Considered for Handrails on Ramps
These technical criteria are available at http://www.access-board.gov/ada-aba/final.cfm#a505 and address continuity, height, clearance, gripping surface, cross section, surfaces, fittings...
-
11B-505.10.3 Bottom extension at stairs
Extension shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent stair flight....
-
11B-606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (864 mm) maximum above the finish floor or ground....
-
11B-606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (864 mm) maximum above the finish floor or ground....
-
1009.5.7 Grab Bars
Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above each step and transfer platform....
-
1002.5 Amusement Ride Seats Designed for Transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
User Management Software: Skills Your Team Needs
This reduces the attack surface by removing unnecessary functions present in normal software....
-
Federal Elevator Carelift Wheelchair Lift
unit of compact design Completely pre-wired car and limit switches Standard Features: 2 Stops 36″ x 60″ Platform size 8″ Pit Depth 80″ Cab Height Swing Entrances Rubber...
-
Wikk Industries Inc. RFID Hand-Free transimitter/With Switch and Bollard Transmitter
Switch and Bollard Transmitter For bollard use, tuck under rubber stop of Wikk standard bollard cap (non-metallic): One model fits all switches....
-
3.13(a) Placement of Wheelchair Spaces
Placement of Wheelchair Spaces Each wheelchair space shall comply with the size requirements set forth in § 4.33.2 of the Standards, be level and satisfy the floor surface requirements...
-
1009.2.4 Seat Height
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
Landings
Landings Landings are the level surfaces at the top and bottom of each ramp run....
