An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....
Search Results "Work Surface"
-
CURB CUT
-
TRANSITION PLATE
[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
-
TRANSITION PLATE
[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
CURB CUT
An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....
-
4. Comparison of Proposed Technical Provisions Applicable to Shared Use Paths and AASHTO Guide
R302.7 Surfaces....
-
M302.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Ramps [4.8]
The curvature and slope typically result in an uneven surface that makes wheelchair maneuvering difficult because not all wheels rest on the surface....
-
Openings in Beach Access Routes
Openings are gaps in the surface of a beach access route. Gaps include spaces between the planks on a boardwalk and drainage holes in temporary or permanent surfaces....
-
Questionnaire
A full version of the questionnaire given to the subjects after traveling over each surface can be found in Appendix C. The questionnaire was developed by the study investigators....
-
M302.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
What should I do if I think I might need a reasonable accommodation?
You may request a reasonable accommodation at any time during the application process or any time before or after you start working....
-
Qualifications
Ability to work cooperatively with the public entity and people with disabilities. Negotiation and mediation skills. Organizational and analytical skills....
-
R103.1 Conventional Industry Tolerances
Conventional industry tolerances do not apply to design work....
-
Q. What is "reasonable accommodation?"
Reasonable accommodation is a modification or an adjustment to a job or the work environment that will enable a qualified applicant or employee with a disability to participate in the application...
-
Q3: Roadway Resurfacing Alteration Project and Curb Ramp Improvements
A3: It depends on whether the resurfacing work affects a pedestrian crosswalk. ...
-
DOT Response
Currently, the Department is considering this issue in the context of the Air Carrier Access Act, and the Department of Justice is reviewing it in the context of ongoing work on its ADA...
-
Sensory Issues
quality Discontinue the use of fragranced products Use only unscented cleaning products Provide scent-free meeting rooms and restrooms Modify workstation location Modify the work...
-
20. When an employee requests leave as a reasonable accommodation, may an employer provide an accommodation that requires him/her to remain on the job instead?
In discussing this request with the employer, the employee states that he could return to work after seven weeks if, during his first three weeks back, he could work part-time and eliminate...