Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
Search Results "Surface Material"
Commonly Searched Documents
-
11B-609.4 Position of grab bars
-
Issue 1: APS volume
Note that nearby building facades or other hard surfaces that reflect the APS signal may actually cause the APS to increase in volume in reaction to its own sound, if the sound or ambient...
-
2. Mirrors
Mirrors: If provided, mirrors need to be mounted with the bottom edge of the reflecting surface no higher than 40 inches above the floor....
-
705.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705. Figure 705.1 Size and Spacing of Truncated Domes...
-
Boat Launch Ramp
A sloped surface designed for launching and retrieving trailered boats and other water craft to and from a body of water....
-
Confirm that the vibrotactile indications work
Confirm that the vibrotactile indications work The tactile arrow or vibrating surface should vibrate rapidly only during the walk interval for the street....
-
5.4.3.1 Positioning Support Height for Imaging Equipment
Positioning supports should be positioned 3 to 6 inches above the transfer surface....
-
R305.2.6 Boarding Platforms
At boarding platforms for buses and rail vehicles, detectable warning surfaces shall be placed at the boarding edge of the platform....
-
e-i
Is the curb ramp surface at least 36 inches wide, excluding flared sides? [ADA Standards § 4.7.3] Yes No...
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2....
-
RAMP
A walking surface that has a running slope steeper than one unit vertical in 20 units horizontal (5-percent slope)....
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2. ...
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2....
-
RAMP
A walking surface that has a running slope steeper than one unit vertical in 20 units horizontal (5-percent slope)....
-
11B-1009.4.5 Grab bars
The top of the gripping surface shall be 4 inches (102 mm) minimum and 6 inches (152 mm) maximum above transfer walls....
-
A. About Appendices 1 and 2
The materials in Appendices 1 and 2 guide surveyors – even those with little or no knowledge of accessibility or experience surveying – through the process of surveying elements in a step-by-step...
-
C. Who should conduct the survey?
Surveyors will naturally gain familiarity with the materials by going out and surveying with them, but it is a good idea to review the forms and instructions before conducting the survey...
-
8. NEEDS + RESOURCES ASSESSMENT
Sample Needs: Sample Resources: Food/water Commodity Distribution Points Clothing/blankets Red Cross Clean up materials Volunteers (Example...
- Bobrick Koala Kare Child Protection Seat Baby Changing Station KB102
- BEA Inc. PBJ Series Jamb Style Push Plates (Push to Open)
- Landscape Forms Inc. Redline Bench Collection
-
RAMP
A walking surface that has a running slope steeper than one unit vertical in 20 units horizontal (5-percent slope)....
-
R305.1 General
Detectable warning surfaces shall consist of truncated domes aligned in a square or radial grid pattern and shall comply with R305....
-
1005.3.1 Curb or Barrier
Curbs or barriers shall extend 2 inches (51 mm) minimum above the surface of the fishing pier or platform....