The guidelines, which the Board originally published in 1991, apply to new or remanufactured vehicles (they also include provisions for rail vehicles that the Board will update separately...
Search Results "Support Rail"
-
8. Transportation Vehicles
-
8. Transportation Vehicles
The guidelines, which the Board originally published in 1991, apply to new or remanufactured vehicles (they also include provisions for rail vehicles that the Board will update separately...
-
12162(b)(2)(B) Accessibility
(B) Accessibility For purposes of section 12132 of this title and section 794 of title 29, a requirement that a rail passenger car used in commuter rail transportation be accessible to...
-
12162(a)(2)(A) General rule
individuals who use wheelchairs, it shall be considered discrimination for purposes of section 12132 of this title and section 794 of title 29 for a person to purchase or lease any new rail...
-
49 CFR Part 37 - Transportation for Individuals With Disabilities at Intercity, Commuter, and High Speed Passenger Railroad Station Platforms; Miscellaneous Amendments
DEPARTMENT OF TRANSPORTATION 49 CFR Parts 37 and 38 [Docket OST–2006–23985] RIN 2105–AD54 Transportation for Individuals With Disabilities at Intercity, Commuter, and...
-
Transfer Supports Location and Configuration M301.3 and M302.3
Transfer Supports Location and Configuration M301.3 and M302.3 Location of the transfer supports shall be a minimum of 6 inches to a maximum of 19 inches from the top of the transfer...
-
8. Transportation Vehicles
These requirements apply to new or remanufactured vehicles covered by the ADA, including: buses and vans rail cars (rapid, light, commuter, intercity, high-speed, and monorail...
-
ADA and Level Boarding - Q&A on Wheelchairs and Bus and Rail Service
DEPARTMENT OF TRANSPORTATION DISABILITY LAW GUIDANCE
-
4.4.3 Backrest and Armrest
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device or supporting...
-
M301.3 Supports (Section-by-Section Analysis)
An editorial change was made to this section as a result of the change in M301.3.2, described below, to replace the word “stirrups” with the term “leg supports.”...
-
§ 38.175(a)
(a) All cars for high-speed rail systems, including but not limited to those using “maglev” or high speed steel-wheel-on-steel rail technology, and monorail systems operating primarily on...
-
§ 37.47(a)
(a) Each public entity that provides designated public transportation by means of a light or rapid rail system shall make key stations on its system readily accessible to and usable by individuals...
-
12162(e)(2) Existing stations
(2) Existing stations
-
§ 38.63(a) Requirement
(a) Requirement. Suitable devices or systems shall be provided to prevent, deter or warn individuals from inadvertently stepping off the platform between cars. Acceptable solutions...
-
§ 38.63 Between-car barriers
[See subsections ...]
-
§ 38.71(c)
(c) If portions of the vehicle are modified in a way that affects or could affect accessibility, each such portion shall comply, to the extent practicable, with the applicable...
-
§ 38.71(b)
(b)
-
§ 38.85 Between-car barriers
Where vehicles operate in a high-platform, level-boarding mode, devices or systems shall be provided to prevent, deter or warn individuals from inadvertently stepping off the...
-
§ 38.71 General
[See subsections ...]
-
§ 38.51 General
[See subsections ...]
-
M301.3.3 Head and Back Support (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed to place the requirements for head and back support for diagnostic equipment used by patients in the supine, prone, or side-lying position in M301...
-
§ 38.111(a)
(a) New, used and remanufactured intercity rail cars, to be considered accessible by regulations in part 37 of this title shall comply with this subpart to the extent required for each type...
-
M305.5 Head and Back Support (Section-by-Section Analysis)
(Section-by-Section Analysis – M302.3.3), the technical requirements for head and back supports from M301 and M302 have been relocated to M305 Supports....
-
M305.3.1 Horizontal Position
Where the support is horizontal, the top of the gripping surface shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....