Section 407.4.8.1 covers the current ADA Standards for visible elevator car position indicators.
Search Results "Patient in Standing Position"
Filters
Commonly Searched Documents
-
Visible Indicators: ADA Standard Section 407.4.8.1
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of...
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the...
-
6.4 Patient Toilet Rooms
Where toilet/bath rooms are provided as a part of a patient bedroom, each patient bedroom that is required to be accessible shall have an accessible toilet/bath room that complies with 4.22...
-
Hill-Rom Sabina® II Sit-to-Stand Mobile Lift Operating the Lift
This video provides general instructions on how to use the Sabina sit-to-stand lifts, including Operation, Charging, Simple Trouble Shooting, Emergency Lowering and Cleaning Instructions...
-
M302.1 General (Section-by-Section Analysis)
The MDE NPRM proposed that all diagnostic equipment used by patients in a seated position must comply with the technical requirements of proposed section M302....
-
5.3.3.1 Transfer Sides Recommendation for Exam Chairs with Fixed Footrests
The current design allows only one long side for transfer, which limits some patient transfers where a patient can use only one side of the body due to paralysis on one side or other such...
-
Figure 802.2.2.2 Lines of Sight Between the Heads of Standing Spectators – Drawing from the U.S. Access Board
-
Figure 802.2.2.1 Lines of Sight Over the Heads of Standing Spectators – Drawing from the U.S. Access Board
-
The Association of Safe Patient Handling Professionals
The Association of Safe Patient Handling Professionals is a 501(c)(3) non-profit organization that brings together like-minded individuals that want to share ideas, support research, and...
-
b. Positioning Supports
within reach of the patient; one commenter (an accessibility consultant) recommended flexibility to allow for design based on use; and the final commenter (a manufacturer) raised concerns...
-
Free-Standing Overhead Lifts
Free-Standing Overhead Lifts Another type of overhead lift is supported from a frame that rests on the floor....
-
6.4 PATIENT TOILET ROOMS
Provide each patient bedroom that is required to be accessible with an accessible toilet room that complies with 4.22 or 4.23....
-
Clear Floor Space: ADA Standard Section 808.3
Each jury box and witness stand shall have, within its defined area, clear floor space complying with 305....
-
M302.2.3 Size
Transfer surfaces shall be 21 inches (610 mm) wide minimum and 17 inches (430 mm) deep minimum. The size of transfer surfaces shall be measured from center points of their opposing...
-
M302.3.2 Leg Supports
Where stirrups are provided, leg supports shall also be provided and comply with M305.4.
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3.
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2.
-
M302.3.1 Transfer Supports
Transfer supports shall be provided for use with transfer sides required by M302.2.4 and shall comply with M305.2.1.1, M305.2.2.1, and M305.2.3 through M305.2.8.
-
M302.2 Transfer Surface (Section-by-Section Analysis)
This is an introductory section.
-
M302.3 Supports (Section-by-Section Analysis)
This is an introductory section. An editorial change was made to this section as a result of the change in M302.3.2, described below, to replace the word “stirrups” with the term...
-
M302.2.2 Size
The transfer surface shall be 21 inches (610 mm) wide minimum and 15 inches (381 mm) deep minimum. Advisory M302.2.2 Size. The size requirements in this section apply only to the...
-
M302.3.1 Transfer Supports
Transfer supports shall be provided for use with the transfer sides required by M302.2.3 and shall comply with M305.2.
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2.
