[See subsections ...]
Search Results "Low Energy Door"
Filters
Commonly Searched Documents
-
Solutions to Enhance Wayfinding (slides 8 -15)
-
Eunice Noell-Waggoner, IES, LC. Value, Contrast and Reflections
(Note: A transcript of this presentation was not available. These edited Proceedings are based on notes by JEW and TOS, and slides that accompanied the presentation) Exterior...
-
1132A.3 Width and height of interior doors and secondary exterior doors
1132A.3 Width and height of interior doors and secondary exterior doors. Doors shall comply with the following:...
-
404.2.4.3 Recessed Doors and Gates
404.2.4.3 Recessed Doors and Gates....
-
11B-404.2.6 Doors in series and gates in series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1219 mm) minimum plus the width of doors or gates swinging into the space....
-
Opening Force
Section 404.2.9 addresses the opening force of doors and gates....
-
404.2.4.3 Recessed Doors and Gates
, measured perpendicular to the face of the door or gate....
-
404.2.4.3 Recessed Doors and Gates
, measured perpendicular to the face of the door or gate....
-
11B-206.5 Doors, doorways, and gates
Doors, doorways, and gates providing user passage shall be provided in accordance with Section 11B-206.5. ...
-
11B-206.5 Doors, doorways, and gates
Doors, doorways, and gates providing user passage shall be provided in accordance with Section 11B-206.5....
-
11B-206.5 Doors, doorways, and gates
Doors, doorways, and gates providing user passage shall be provided in accordance with Section 11B-206.5....
-
404.2 Manual Doors, Doorways, and Manual Gates
404.2 Manual Doors, Doorways, and Manual Gates. Manual doors and doorways and manual gates intended for user passage shall comply with 404.2....
-
11B-404.2.6 Doors in series and gates in series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1219 mm) minimum plus the width of doors or gates swinging into the space....
-
11B-404.2.6 Doors in series and gates in series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1219 mm) minimum plus the width of doors or gates swinging into the space....
-
Issue 21: What additional education and training are needed for supervisors of employees with low vision?
But I just am only suggesting that that the areas where you might have not only a greater impact but also areas where, as Kurt has suggested, you may be able to marry the low vision issue...
-
Shower and Sauna Doors in Transient Lodging Facilities
Shower and Sauna Doors in Transient Lodging Facilities....
-
Door Maneuvering Clearance
Table 404.2.4.1 specifies maneuvering clearances for manual swinging doors and gates....
-
224.1.2 Guest Room Doors and Doorways
224.1.2 Guest Room Doors and Doorways....
-
224.1.2 Guest Room Doors and Doorways
Advisory 224.1.2 Guest Room Doors and Doorways....
-
F224.1.2 Guest Room Doors and Doorways
Advisory F224.1.2 Guest Room Doors and Doorways....
-
Value Contrast (slide 9)
Even if you’re looking down and expecting to have to look for a clear path, those are very hard to see, because they’re quite low. A lot of those benches are knee height or below....
-
Maneuvering Space at Doors
Several commenters requested that the final Guidelines incorporate minimum maneuvering clearances at doors, as provided by the ANSI Standard....
-
404.2.2 Double-Leaf Doors and Gates
At least one of the active leaves of doorways with two leaves shall comply with 404.2.3 and 404.2.4.
-
404.2.2 Double-Leaf Doors and Gates
At least one of the active leaves of doorways with two leaves shall comply with 404.2.3 and 404.2.4.