(3) Application of force: Apply force gradually so that the applied force does not exceed the resistance of the door....
Search Results "Ligature Resistant"
Filters
Commonly Searched Documents
-
A4.13.11(3) Application of force
-
A4.13.11(3) Application of force
(3) Application of force: Apply force gradually so that the applied force does not exceed the resistance of the door....
-
5.4.11 Transfer Support Structural Strength Recommendations for M301 and M302
5.4.11 Transfer Support Structural Strength Recommendations for M301 and M302 Description: Transfer supports and their connections must be capable of resisting sufficient vertical and...
-
1134A.6, Item 2
The floor surfaces shall be of Carborundum or grit-faced tile or of material providing equivalent slip resistance....
-
1134A.6, Item 2
The floor surfaces shall be of Carborundum or grit-faced tile or of material providing equivalent slip resistance....
-
11B-809.10.6.2 Slope
The floor surfaces shall be of Carborundum, grit-faced tile or of material providing equivalent slip resistance....
-
5.4.11 Transfer Support Structural Strength for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer supports and connections must contain the strength to resist vertical and horizontal forces of 250 pounds at locations determined by the intended use of the equipment....
-
Wheelchair accessible seating is required. At least one percent of the seating must be wheelchair seating locations.
Each wheelchair seating location is an open, level space that accommodates one person using a wheelchair and has a smooth, stable, and slip-resistant surface....
-
Tandem Recumbent Bicycles
Tandem recumbent bicycles have the potential for fairly high cruising speeds due to the lower wind resistance of a recumbent combined with the additional energy output of a tandem....
-
Exit Stairway Enclosures [IBC §1007.3 and 1019 (2003), §1003.2.13.2 and 1005.3.2 (2000)]
The IBC contains requirements for exit stairway enclosures that address fire-resistance and smoke protection, stairways and handrails, signs, and other features....
-
11B-302.2 Carpet
Carpets and permanently affixed mats can significantly increase the amount of force (roll resistance) needed to propel a wheelchair over a surface....
-
11B-302.2 Carpet
Carpets and permanently affixed mats can significantly increase the amount of force (roll resistance) needed to propel a wheelchair over a surface....
-
11B-302.2 Carpet
Carpet and permanently affixed mats can significantly increase the amount of force (roll resistance) needed to propel a wheelchair over a surface....
-
BACKGROUND
the following recommendation: 5.4.11 Transfer Support Structural Strength Recommendations for M301 and M302 Description: Transfer supports and their connections must be capable of resisting...
-
711.3.1.2 Through-penetration firestop system
installed as tested in accordance with ASTM E 814, with a minimum positive pressure differential of 0.01 inch (2.49 Pa) of water and shall have an F rating of not less than the required fire-resistance...
-
1017.2 Surface
A firm trail surface resists deformation by indentations....
-
§ 38.83(c)(2) Ramp surface
The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater then 1/4 inch, shall have a clear width of 30 inches, and shall...
-
704.2.3 Combustible projections
Combustible projections located where openings are not permitted or where protection of openings is required shall be of at least 1-hour fire-resistance-rated construction, Type IV construction...
-
POWER-ASSISTED DOOR
A door used for human passage with a mechanism that helps to open the door, or relieve the opening resistance of a door, upon the activation of a switch or a continued force applied to the...
-
1017.2 Surface
A firm trail surface resists deformation by indentations....
-
1017.2 Surface
A firm trail surface resists deformation by indentations....
-
§ 38.95(c)(2) Ramp surface
The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater than 1/4 inch high, shall have a clear width of 30 inches and...
-
§ 38.125(c)(2) Ramp surface
The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater than 1/4 inch high, shall have a clear width of 30 inches and...
-
704.9 Vertical separation of openings
Such openings shall be separated vertically at least 3 feet (914 mm) by spandrel girders, exterior walls or other similar assemblies that have a fire resistance rating of at least 1 hour...