The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2....
Search Results "Back Support"
-
M305.2.2 Length
-
M305.2.3 Height (Section-by-Section Analysis)
The MDE Advisory Committee supported adding a requirement setting the height of transfer supports within the range described in question 20 in the MDE NPRM preamble, of 6 inches minimum...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings....
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports....
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum....
-
Mockett DH3/BB Square Door Handle Back to back
Sold individually or as a pair with back-to-back mounting hardware available. Size: 13" overall length, 12" center to center, 2-3/4" projection, 1" square....
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2....
-
M305.2.1 Location (Section-by-Section Analysis)
The Committee recommended requiring one support on the opposite side of the transfer side regardless of whether it was a transfer support or positioning support....
-
M305.2.5 Surface Hazards
Transfer supports and surfaces adjacent to transfer supports shall be free of sharp or abrasive components and shall have eased edges....
-
Service Animal Issues
Another important issue that a number of commenters raised concerned “emotional support animals.”...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position....
-
Mockett DH403-BB Square Bar Door Handle Back to Back
Back to back mounting hardware included. Size: 325mm (12-25/32") length, 300mm (11-13/16") center to center and 65mm (2-9/16") projection....
-
Mockett DH401-BB Slim Barrel Door Handle Back to Back
Back to back mounting hardware included. Size: 400mm (15-3/4") length, 300mm (11-13/16") center to center and 60mm (2-3/8") projection....
-
Maintenance and Back-Up
In addition to this specific maintenance requirement, the ADA's equal access requirement obligates PSAPs to implement equally effective procedures for maintenance and back-up capability...
-
Service and Companion Animal Owners: Know Your Rights!
Service and Companion Animal Owners Service and companion animals can help people with disabilities go about their daily lives. Unfortunately, there’s still a lot of confusion...
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed transfer surface...
-
M305.2.5 Surface Hazards (Section-by-Section Analysis)
The proposed rule did not provide any specific restrictions regarding surface hazards around the transfer supports....
-
Mockett DH2A/BB-SSS Curved Door Handle Back to back Small
Back to back mounting hardware included. Size: 249mm (9-13/16") long, 224mm (8-13/16") O.C., 55mm (2-5/32") projection. Also sold individually: DH2A-SSS ....
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
This revision to provide options for two types of transfer surfaces necessitated adding additional technical criteria addressing transfer surface size (M301.2.3) and transfer supports (M305.2...
-
Mockett DH2B/BB-SSS Curved Door Handle Back to back Medium
Back to back mounting hardware included. Size: 425mm (16-23/32") long, 400mm (15-3/4") O.C., 55mm (2-5/32") projection. Also sold individually: DH2B-SSS ....
