A2.) The design itself must always call for conditions that meet the specific standards. Tolerances are not an “oops factor” for careless or sloppy design. They are instead...
Search Results "Advisory Committee"
Filters
Commonly Searched Documents
-
Q2.) What are the types of “field conditions” that were anticipated where the advisory says “tolerances recognized by this provision include those for field conditions”?
-
Issue 23: Should design guidance for persons with low vision be prescriptive or performance based?
We need that sort of thing, that sort of participation on the ANSI committee....
-
BACKGROUND
BACKGROUND Section 5.4.11 of the Committee report makes the following recommendation: 5.4.11 Transfer Support Structural Strength Recommendations for M301 and M302 Description:...
-
Background
Advisory information in the guidelines discusses the use of a Rotational Penetrometer to measure the firmness and stability of surfaces that are located on trails. According to U.S....
-
4.5 Weight Scales
All standard size manual wheelchairs, powered wheelchairs, small to mid-range scooters, and most extra wide manual chairs can be accommodated through the Committee’s recommendations (see...
-
A. Background
In developing these draft guidelines, the Access Board obtained recommendations from an Advisory Committee composed of representatives from disability organizations, public works departments...
-
Federal Trail Data Standards
Federal Trail Data Standards—Standards that are published by the Federal Geographic Data Committee....
-
M302.2 Transfer Surface
• Sub-Committee Recommendation: No revision as a stretcher chair should be the equivalent of a mobile examination chair....
-
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum and width...
-
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height Recommendations
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height Recommendations The Committee recommends that no edge protection be required on platforms of 1½ inches or less in height...
-
4.4.2 Mammography Equipment and Scooters
4.4.2 Mammography Equipment and Scooters The Committee considered the interaction of women who use scooters with mammography equipment....
-
5.4.7 Transfer Support Gripping Surface Clearance Recommendation for M301 and M302
The Committee recommends following the Access Board’s proposal in the preamble discussion allowing a 1½-inch clearance....
-
M301.2.3 Transfer Sides
• Sub-Committee Recommendation: The transfer surface shall be located to provide options to transfer from a mobility device onto both long sides (length), right and left, of the surface...
-
Section 37.73 Purchase or Lease of Used Non-Rail Vehicles by Public Entities Operating a Fixed Route System
The reports of the Senate Committee on Labor and Human Resources and the House Committee on Education and Labor offered the following guidance on what “good faith efforts” involve: The...
-
C.
As for committee reports, they are drafted by committee staff and are not voted on (and rarely even read) by the committee members, much less by the full house....
-
SHOULD
[DSA-AC] Denotes an advisory specification or recommendation....
-
11B-405.3 Cross slope
Advisory 11B-405.3 Cross slope. Cross slope is the slope of the surface perpendicular to the direction of travel....
-
Moving to the House Floor
Moving to the House Floor The ADA proceeded rapidly to the House floor after the Judiciary Committee completed its work....
-
203.9 Employee Work Areas
The ADAAG Review Advisory Committee recommended that ADAAG be changed to require an accessible route to each "individual work station" instead of to "work areas."...
-
Section 1630.1(b) Applicability
The ADA defines “covered entities” to mean an employer, employment agency, labor organization, or joint labor-management committee. 42 U.S.C. 12111(2)....
-
SEC. 105. POSTING NOTICES. 42 USC 12115
Every employer, employment agency, labor organization, or joint labor-management committee covered under this title shall post notices in an accessible format to applicants, employees, and...
-
5.4.3.1 Positioning Support Height Recommendation for Imaging Equipment with Transfer Surfaces
5.4.3.1 Positioning Support Height Recommendation for Imaging Equipment with Transfer Surfaces For imaging equipment with transfer surfaces, the Committee recommends a positioning support...
-
Introductory Statements
Chairman and Members of the Committee: Thank you for your invitation to present my views to the Committee....
-
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301)
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301) The Committee recommends a transfer surface size on imaging equipment be a minimum of 28 inches long by a minimum...