protrude a distance of 6 inches (152 mm) maximum along the front of the wheelchair space, where located 9 inches (229 mm) minimum and 27 inches (686 mm) maximum above the floor or ground surface...
Search Results "Check Writing Surface"
-
11B-1002.4.4.3 Permitted protrusions in wheelchair spaces
-
11B-801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
11B-1002.4.4.3 Permitted protrusions in wheelchair spaces
protrude a distance of 6 inches (152 mm) maximum along the front of the wheelchair space, where located 9 inches (229 mm) minimum and 27 inches (686 mm) maximum above the floor or ground surface...
-
Energy Consumption During Ambulation
Subjects walked on each surface at their preferred pace, until the physiological variables (energy consumption, heart rate, velocity) had stabilized (2‒3 minutes) and the data collection...
-
R306.3.1 Separation
Detectable warning surfaces shall not be used for edge treatment....
-
3. Terminology
Discussion—Elevation measurements may be taken statically, as with rod and level per Test Method E1364 or dynamically using a rolling inclinometer per Test Method E2133. 3.1.1.2 traveled surface...
-
Selection of Methodology
) information (product type, manufacturer name, warranty/guarantees’ information, and similar data) SECTION #3 Trail pre‐installation specifications (soil type/composition, slope of surface...
-
Road Roughness Measurements
These RTRRMS systems recorded cumulative axle displacement over a given distance and thus reported surface roughness as inches/mile....
-
Key Differences Between Routes
when necessary for drainage —1:20 (5%) 1:20 (5%) 1:12 (8.33%) 200 feet Concrete, asphalt, boards—1:48 (2%) All other surfaces when necessary for...
-
Enhancing Airport Wayfinding for Aging Travelers and Persons with Disabilities
Wayfinding Accessibility Audit Checklist documents issues that should be considered in a baseline airport wayfinding accessibility audit; it is provided in Word format so that users can check...
-
11B-411.2.1.6 Identification of floors served
consoles located on floors with a building entry, including parking and transfer levels, shall be provided with signs complying with Sections 11B-703.2, 11B-703.3, and 11B-703.5 on the surface...
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
11B-411.2.1.6 Identification of floors served
consoles located on floors with a building entry, including parking and transfer levels, shall be provided with signs complying with Sections 11B-703.2, 11B-703.3, and 11B-703.5 on the surface...
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3....
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
M301.3 Supports
Transfer supports, leg supports, and reclining surfaces shall comply with M301.3....
-
Berm
Berm - A sloped surface at ground level designed to ascend or descend in elevation....
-
106.5.53 Ramp
A walking surface that has a running slope steeper than 1:20....
-
Maintenance and Back-Up
If PSAPs check their voice telephone equipment every day to make sure it is working, they must do so every day for TTY equipment....
-
§ 382.45 Passenger information
interfere with crewmembers’ safety duties as set forth in FAA regulations) including, but not limited to, information concerning ticketing, flight delays, schedule changes, connections, flight check-in...
-
§ 382.40a Boarding assistance for large aircraft
(3) Under the agreement, carriers may require that passengers wishing to receive boarding assistance requiring the use of a lift for a flight check in for the flight one hour before...
-
C. Developing an Action Plan For Providing Accessible Websites
Check the HTML of all new webpages. Make sure that accessible coding is used....
-
M305.2.2 Length (Section-by-Section Analysis)
extend horizontally along the transfer surface to within three inches, to allow for manufacturing tolerances....
