Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
Search Results "Surface Material"
-
11B-1002.6 Transfer devices for use with amusement rides
-
2.3.3 Issues
However, line of sight reception is affected by surface material (light surfaces reflect more light energy), the strength of the transmitted signal, and the geometric shape and number of...
-
Pressalit Care PLUS Support Arm Height Adjustable Swing Grab Bar
Materials: The arms are constructed of 10-micrometre anodized aluminum, with a non-slip gripping surface made of soft SEBS incorporating a glass-reinforced nylon core....
-
Pressalit Care PLUS Support Arm Height and Sideways Adjustable Swing Grab Bar
Materials: The arms are construced of 10-micrometre anodized aluminium, with a non-slip gripping surface made of soft SEBS incorporating a glass-reinforced nylon core....
-
ALIGNMENT OF 19-INCH RECOMMENDATION WITH ACCESS BOARD PROPOSED RULEMAKING
In its proposed rule, the Access Board proposed that the “height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured...
-
11B-1003.2.1 Boat slips
The vertical distance is 10 feet (3050 mm) between the elevation where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level....
-
Boat Slips: ADA Standard Section 1003.2.1
Where handrail extensions are provided on gangways or transition plates, the handrail extensions shall not be required to be parallel with the ground or floor surface. 7....
-
11B-1003.2.1 Boat slips
The vertical distance is 10 feet (3050 mm) between the elevation where the gangway departs the landside connection and the elevation of the pier surface at the lowest water level....
-
5.4.1.2 Transfer and Positioning Support Location for Imaging Equipment
Transfer supports should be provided for imaging equipment with transfer surfaces with depths of less than or equal to 24 inches....
-
Willoughby Industries WBL-2320 Ligature-resistant Behavioral Healthcare Lavatory System
The lavatory system bowl with integral sloped backsplash is constructed of Aquasurf® molded cast polymer densified solid surface material composed of polyester/acrylic resin, UV stabilizer...
-
Slope
The incline of a surface....
-
Slope
The incline of a surface. ...
-
Landscape Forms Inc. Petoskey Bench Collection
Refer to materials/colors link on this page to view standard selections. FSC® certified woods available....
-
Pilot Rock HRE and HRP Hitching Post Bike Rack
Specifications: MATERIALS: Constructed from heavy 2-3/8" OD steel pipe....
-
Edge Protection
Edge Protection Where railings, guards, or handrails are provided, edge protection must be provided and extend a minimum of 2 inches above the ground or deck surface....
-
SEAT HEIGHT MEASUREMENT DETAIL
Note that examination tables and chairs only use bolsters on certain areas of the transfer surface....
-
1.3.2 Focus Following NPRM Comments
This review identified four major issue areas for the MDE Advisory Committee to address, as follows: Transfer surface height and size Permitted obstructions to the transfer surface...
-
I. Public Toilet Rooms
In all public and common use toilet rooms throughout the Hotel and the Tower, Defendants will provide at least one lavatory with a counter-top that is 34 inches above the finish floor surface...
-
Card Catalogs and Magazine Displays [8.4]
Requirements for fixed counters and tables [4.32] specify a surface height (34 inches maximum) and knee clearance below appropriate for extended use as a writing/work surface....
-
Bradley 2-Station Express Crescent Lavatory System CRS-2
access panel/ trap cover required) Serves 1 - 2 users at a time Sleek, low-profile, contemporary design, Only 38" High Constructed of vandal resistant Terreon or TerreonRE Solid Surface...
-
Landscape Forms Inc. Chase Park Bench Collection
Chase Park seats may be specified as two- or three-seat units All units are backed Intermediate arms may be specified for multiple seat units Bench materials consist of cast aluminum...
-
PEMKO 7" Half Saddle/Offset Saddle Threshold No. 2727
About Commercial Thresholds Pemko manufactures thresholds in several materials to meet customer needs. Extruded Aluminum thresholds are manufactured of tempered aluminum, 6063-T6....
-
PEMKO 5" Latching Panic Saddle Threshold No. 2005-V
About Commercial Thresholds Pemko manufactures thresholds in several materials to meet customer needs. Extruded Aluminum thresholds are manufactured of tempered aluminum, 6063-T6....
-
PEMKO 5" Latching Panic Saddle Threshold No. 2005-P
About Commercial Thresholds Pemko manufactures thresholds in several materials to meet customer needs. Extruded Aluminum thresholds are manufactured of tempered aluminum, 6063-T6....
