Support rails in elevator cabs are used in a different way than handrails along a walking surface such as a ramp or stairway....
Search Results "Recreational Surfacing"
Filters
Commonly Searched Documents
-
11B-407.4.10 Support rail
-
DETECTABLE WARNING
A standardized surface feature built in or applied to walking surfaces or other elements to warn persons with visual impairments of hazards on a circulation path....
-
Final Regulatory Flexibility Analysis
surfaces where the ball could not come to rest....
-
Spectrum Industries Inc. Freedom One Sit-to-Stand Lectern
With the push of a button, a whisper quiet electrical lift adjusts the height of the entire work surface. ...
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
M301.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
903.4 Back Support
Back support shall be 42 inches (1065 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (455 mm) minimum above the seat...
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
Bed Height Fact Sheet
An individual can arrive at a lodging facility where parking, check-in, restrooms, elevators, recreational centers, the path of travel to the room, and room amenities are all accessible-except...
-
Tread Width
The visible trail surface measured perpendicular to the direction of travel....
-
11B-411.2.1.6 Identification of floors served
consoles located on floors with a building entry, including parking and transfer levels, shall be provided with signs complying with Sections 11B-703.2, 11B-703.3, and 11B-703.5 on the surface...
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
Title III - Private Entities
accommodations are private entities that own, lease, lease to, or operate facilities such as restaurants, stores, hotels, theaters, private schools, doctors' offices, day care centers, and recreation...
-
Road Roughness Measurements
These RTRRMS systems recorded cumulative axle displacement over a given distance and thus reported surface roughness as inches/mile....
-
3. Terminology
Discussion—Elevation measurements may be taken statically, as with rod and level per Test Method E1364 or dynamically using a rolling inclinometer per Test Method E2133. 3.1.1.2 traveled surface...
-
Selection of Methodology
) information (product type, manufacturer name, warranty/guarantees’ information, and similar data) SECTION #3 Trail pre‐installation specifications (soil type/composition, slope of surface...
-
R306.3.1 Separation
Detectable warning surfaces shall not be used for edge treatment....
-
Energy Consumption During Ambulation
Subjects walked on each surface at their preferred pace, until the physiological variables (energy consumption, heart rate, velocity) had stabilized (2‒3 minutes) and the data collection...
-
11B-801.1 Scope
For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
M302.4.2 Clearance Around Base
the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.2 Clearance Around Base
base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
MEASUREMENT TECHNIQUE
MEASUREMENT TECHNIQUE The depth and width are measured along the centerlines of the seat, and the height from the floor to the highest point of the transfer surface: The depth...
