must be based on an individualized assessment, based on reasonable judgment that relies on current medical evidence or on the best available objective evidence, to determine: the nature, duration...
Search Results "Expected Maximum Flight Duration"
-
Qualified individual with a disability (Section-by-Section Analysis)
-
B. Survey and Review of Polling Place Locations
For the duration of this Agreement, when the County selects a new polling place location, the County will provide the United States notice within twenty-one (21) days of the decision....
-
ADOPTION AND IMPLEMENTATION OF EFFECTIVE COMMUNICATION POLICY
The training program, the materials for which shall be approved in advance by the United States, shall be no less than one hour in duration, shall be conducted separately from any training...
-
Flush Controls on Toilets
Hand operated flush controls shall comply with 309.2 and 309.4 and shall be installed 36 inches (915 mm) maximum above the finish floor....
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter 0.059...
-
11B-1009.3.3 Handrails
The clear width between required handrails shall be 33 inches (838 mm) minimum and 38 inches (965 mm) maximum. Exceptions: 1. ...
-
Chapter 3: Building Blocks
Substantive revisions made in the final rule include: lowering the maximum height for side reaches from 54 to 48 inches (308.3.1) providing a limited exception from this...
-
610.3 Shower Compartment Seats
The top of the seat shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. Seats shall comply with 610.3.1 or 610.3.2....
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions Measurement Range Minimum in Inches Maximum in Inches Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
F228 Depositories, Vending Machines, Change Machines, and Mail Boxes
These elements are subject to requirements for operable parts in section 309, which specify location within accessible reach ranges and maximum operating forces....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
Tax Credits and Deductions
The tax deduction is available to all businesses with a maximum deduction of $15,000 per year....
-
610.3 Shower Compartment Seats
The top of the seat shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. Seats shall comply with 610.3.1 or 610.3.2. ...
-
Parking Spaces [4.6.3]
A maximum slope of 2% is required in all directions for both the space and access aisle since level surfaces are important for wheelchair transfer to and from vehicles....
-
2. a. Accessible route into and throughout the facility
The accessible route shall, to the maximum extent feasible, coincide with the route for the general public....
-
Location [§208.3]
A maximum travel distance is not specified in the Standards....
-
11B-704.4.1 Height
wheelchair accessible telephone because the required 34 inches (865 mm) minimum keypad height can causes the highest operable part of the telephone, usually the coin slot, to exceed the maximum...
-
11B-704.4.1 Height
wheelchair accessible telephone because the required 34 inches (865 mm) minimum keypad height can causes the highest operable part of the telephone, usually the coin slot, to exceed the maximum...
-
11B-703.7.2.6 Toilet and bathing facilities geometric symbols
Geometric symbols at entrances to toilet and bathing rooms shall be mounted at 58 inches (1473 mm) minimum and 60 inches (1524 mm) maximum above the finish floor or ground surface measured...
-
1115B.4.1, Item 1
The centerline of the accessible water closet shall be 16 inches (405 mm) minimum and 18 inches (457 mm) maximum from the side wall or partition....
-
5.4.4 Transfer Support Distance from Transfer Surface Recommendations for M301 and M302
The gripping surface of the transfer support should be located 1 ½ inches maximum measured horizontally from the adjacent edge of the transfer surface....
-
Alterations to Existing Facilities
Alterations to Existing Facilities The draft guidelines required alterations to existing facilities to comply with the requirements for new construction to the maximum extent feasible...
-
M301.4 Lift Compatibility
Equipment components are permitted to be located within 8 inches (205 mm) maximum of the centerline of the clearance width....