Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (12.7 mm) maximum within 10 inches (254 mm) horizontally of the minimum landing area...
Search Results "Expected Maximum Flight Duration"
-
11B-405.9 Edge protection
-
11B-1009.3.3 Handrails
The clear width between required handrails shall be 33 inches (838 mm) minimum and 38 inches (965 mm) maximum....
-
Accessible Boat Slips
Edge protection is not required, but if provided, it can be 4 inches high maximum and 2 inches deep maximum at the continuous clear openings....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
R211 Signs (Section-by-Section Analysis)
In the 2004 ADA and ABA Accessibility Guidelines, characters on bus route signs must comply with the technical requirements for character height “to the maximum extent practicable."37 The...
-
11B-604.5.1 Side wall
The side wall grab bar shall be 42 inches (1067 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1372 mm) minimum from the rear wall with...
-
2.5 Visual Detection Distance
As described in the Method section, the maximum distance up to 7.92 m (26 ft) at which each participant could see each detectable warning was measured....
-
Smith System Planner Access Station 24″ Deep Table
Provides maximum strength and stability for two students and computers, plus great security for cables and wires thanks to a locking wireway. Comes with backpack pegs....
-
Behavioral Safety Products #BF935 Suicide Resistant Attenda 4 Shelf Storage Unit
suicide resistant four shelf storage unit is composed of high impact polyethylene, abuse-resistant, heavy gauge material, and is formed from a one piece, rotationally molded design for maximum...
-
Cavity Sliders CL100 ADA LaviLock Hardware Set with 'Vacant / In Use' Indicator
Slide Locking Buttons including Emergency Release CL100 Mortise Lock Case IMPORTANT: Operable parts of hardware must be mounted 34 inches (865mm) minimum and 48 inches (1220 mm) maximum...
-
Behavioral Safety Products #BF930 Suicide Resistant Attenda 3 Shelf Storage Unit
suicide resistant three shelf storage unit is composed of high impact polyethylene, abuse-resistant, heavy gauge material, and is formed from a one piece, rotationally molded design for maximum...
-
Brewer Access™ High-Low Exam Table 700
with Brewer's signature pass-through drawer system and it's backed by Brewer's standard 3-year warranty. 700 lb weight capacity Standard 3-year warranty Unique safety features Maximum...
-
AJW Architectural Products U815 Dual Toilet Tissue Dispenser w/ Mounted Shelf - Surface Mounted - Non-Controlled
Brackets: Fabricated of #18 gauge stainless steel formed for maximum strength. Toilet Tissue Dispenser: Fabricated of stainless steel with a #4 satin finish....
-
Stanley FBB 269 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface area for maximum...
-
Palmer Fixture BluStorm® Bolt High Speed Hand Dryer HD0923
outlets - high drying efficiency, quiet operation Thin profile, protrudes from the wall less than 4" Wide drying area with blue action light indicating sensor range and maximum...
-
Stanley FBB 266 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface area for maximum...
-
Stanley FBB 268 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface area for maximum...
-
Stanley FBB 264 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface area for maximum...
-
2.3.3 Comparison of Dimensions with Standards and other Anthropometric Studies
• Maximum Forces for Hand-operated Controls: Compared to the maximum hand grip strength in a power grip, and lateral and thumb-forefinger pinch grips....
-
Section 37.42
This demonstration must clearly state how the railroad expects that their operations will provide safe and dignified service to the users of such lifts....
-
Section 37.42 Service in an integrated setting to passengers at intercity, commuter, and high-speed rail station platforms constructed or altered after February 1, 2012
This demonstration must clearly state how the railroad expects that their operations will provide safe and dignified service to the users of such lifts....
-
19 Inch Low Height
It is not unreasonable to expect that table and chair manufacturers will seek to compete by offering products with greater degrees of adjustability. Figure 3....
-
Westchester Disabled On the Move, Inc., (WDOMI) - Yonkers, NY
WDOMI expects consumers to be active participants in achieving their goals...
