[ADA Stds 4.8.4] Note: The level landing may be part of the sidewalk or walking surface. Yes _____ No _____...
Search Results "Tread Surface"
Commonly Searched Documents
-
6c. Ramp Landing
-
B3. Access Aisle
[ADA Stds 4.6.6] Note: Unlike an accessible parking space, the surface for the access aisle does not have to be marked or striped. Yes _____ No _____...
-
4.8.7 Edge Protection
Ramps and landings with drop-offs shall have curbs, walls, railings, or projecting surfaces that prevent people from slipping off the ramp....
-
4.8.7 EDGE PROTECTION
Ramps and landings with drop-offs shall have curbs, walls, railings, or projecting surfaces that prevent people from slipping off the ramp....
-
4.6.3 Eyepiece
periscope that is usable from a seated position for viewing each point of interest shall be positioned 43 inches (1090 mm) minimum and 51 inches (1295 mm) maximum above the floor or ground surface...
-
11B-246.7 Trails and paths
Buildings and other functional areas shall be served by paths or walks with firm and stable surfaces....
-
11B-1002.4.4.1 Width and length
Wheelchair spaces shall provide a clear width of 30 inches (762 mm) minimum and a clear length of 48 inches (1219 mm) minimum measured to 9 inches (229 mm) minimum above the floor surface...
-
11B-246.7 Trails and paths
Buildings and other functional areas shall be served by paths or walks with firm and stable surfaces....
-
11B-1002.4.4.1 Width and length
Wheelchair spaces shall provide a clear width of 30 inches (762 mm) minimum and a clear length of 48 inches (1219 mm) minimum measured to 9 inches (229 mm) minimum above the floor surface...
-
Summary of the project
Summary of the project Throughout the course of the project representatives from various trade organizations that represent the following materials that may be used for exterior surfaces...
-
1009.5.7 Grab Bars
Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above each step and transfer platform....
-
11B-1002.5 Amusement ride seats designed for transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.5 Amusement Ride Seats Designed for Transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
Transfer Platforms
can use to lift or transfer onto the play structure and leave the wheelchair or mobility device behind at ground level. 11 inches (280 mm) to 18 inches (455 mm) height of top surface...
-
1002.5 Amusement Ride Seats Designed for Transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
Finish and Contrast [4.30.5]
Consideration should also be given to light sources and the ambient lighting to prevent glare on sign surfaces....
-
Roughness Measurement
The surface profiles were measured with a custom-built pathway measurement tool (PathMeT), which was created from a power WC frame that was instrumented with a wheel encoder and an Acuity...
-
1014.2.1 Transfer Access
The surface of the clear ground space is required to be firm and stable, and to slope not steeper than 1:48 in any direction....
-
1.1.16 Alternate measurement tools
Measure running slope along the same lines of measurements as stated in Section 1.1.13 Although the F - number system can be used to measure surface flatness for smooth surfaces it requires...
-
M102.1 Defined Terms
The following terms are defined in the proposed standards: Enforcing authority, medical diagnostic equipment, operable parts, and transfer surface....
-
Section 35.151(i) Curb ramps (Section-by-Section Analysis)
Upon further consideration, however, the Department has concluded that the regulation should acknowledge that there are times when there are transitions from sidewalk to road surface that...
-
11B-1002.5 Amusement ride seats designed for transfer
Where possible, designers are encouraged to locate the ride seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
11B-1009.5.7 Grab bars
Where a grab bar is provided on each step, the tops of gripping surfaces shall be 4 inches (102 mm) minimum and 6 inches (152 mm) maximum above each step and transfer platform....
-
ยง 38.159(c)(8) Handrails
grasp them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches (760 mm) above the ramp surface...