Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
1015.2 Where required
-
Aisle Ramps in Assembly Areas
In assembly areas, aisle ramps required to be accessible are exempt from some handrail requirements....
-
11B-1002.2 Accessible routes
Exceptions: In load or unload areas and on amusement rides, where compliance with Section 11B-405.2 is not structurally or operationally feasible, ramp slope shall be permitted...
-
Diagonal Curb Ramps [§406.6]
Diagonal Curb Ramps [§406.6] If curb ramps are placed diagonally at an intersection, it is important that clear space 48” long min. is available at the bottom that is outside active...
-
Surfaces for Outdoor Recreation Access Routes
Firm and stable surfaces prevent assistive devices from sinking into the surface....
-
Surface discontinuities
Differences in level between two adjacent surfaces. Elevation changes due to ramps or stairs do not, themselves, constitute surface discontinuities....
-
1013.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, stairs, ramps and landings that are located more than 30 inches (762 mm) measured vertically...
-
1015.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
-
1.1.14 Flatness of ramp cross slope
1.1.14 Flatness of ramp cross slope....
-
106.5.53 Ramp
A walking surface that has a running slope steeper than 1:20....
-
T302.4 Surface Discontinuities
Surface discontinuities shall be ½ inch (13 mm) high maximum and shall be beveled with a slope not steeper than 1:2. EXCEPTIONS: 1....
-
Stabila, Inc. Magnetic TECH Digital Electronic Level Video
Requires the Registered User plan or above. Login! -
1015.5 Surface
This section requires the surface of the clear ground space and turning space to be firm and stable....
-
1.2.1 Walks and other non - ramp surfaces
1.2.1 Walks and other non - ramp surfaces. When overall running slope for walks is measured according to Section 1.1.3 a recommended tolerance for running slope is +1%....
-
Check Writing Surfaces: ADA Standard Section 904.3.3
Where provided, check writing surfaces shall comply with 902.3....
-
7. Exterior Ramp Running Slope
7. ...do the exterior ramps have running slopes of 1:12 or less (critical dimension of 2" or less)?...
-
4.1.6(3)(a) Ramps
(a) Ramps: Curb ramps and interior or exterior ramps to be constructed on sites or in existing buildings or facilities where space limitations prohibit the use of a 1:12 slope or less may...
-
Suspicious Minds Ramp
Suspicious Minds Ramp: p. The ramp leading to the exhibits has a rise greater than 6", but does not have the required handrails on both sides. See Standards § 4.8.5. q....
-
SafeLane® Surface Overlay in Action
Protecting people, roads and infrastructure, SafeLane® surface overlay from Cargill Deicing Technology is the only pavement overlay with anti-icing capabilities....
-
406 Curb Ramps
406 Curb Ramps...
-
Can handrails overlap ramp landings?
This also applies to landings required to be at least 60” by 60” where ramps change directions so that the minimum landing area remains clear....
-
3.2.3 Surface
The ground surface in all camp living areas shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
10.2.1(1)
(1) Where new bus stop pads are constructed at bus stops, bays or other areas where a lift or ramp is to be deployed, they shall have a firm, stable surface; a minimum clear length of 96...
-
Performance for Surface Firmness and Stability
Performance for Surface Firmness and Stability Table 1 identifies the 11 test surface materials, the dates of installation, and the date of the initial and final testing of surfaces at...
