Spout outlets shall be 36 inches (914 mm) maximum above the finish floor or ground.
Search Results "Low Energy Door"
Filters
Commonly Searched Documents
-
11B-602.4 Spout height
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers.
-
404.2.6 Doors in Series and Gates in Series
404.2.6 Doors in Series and Gates in Series....
-
404 Doors, Doorways, and Gates
404 Doors, Doorways, and Gates...
-
4.17.5* DOORS
Toilet stall doors shall comply with 4.13....
-
AUTOMATIC DOOR
A door equipped with a power operated mechanism and controls that open and close the door automatically upon receipt of a momentary actuating signal....
-
AUTOMATIC DOOR
A door equipped with a power operated mechanism and controls that open and close the door automatically upon receipt of a momentary actuating signal....
-
Are closet doors and pantry doors required to comply?
Requirements for doors, doorways, and gates in §404 apply to those that provide “user passage” (§206.5). Doors serving walk-in closets or pantries must comply....
-
11B-411.3.2 Operation
Elevator hoistway and car doors shall open and close automatically....
-
18.1 Q. Is it necessary to provide usable doors when the door leads to an area of the dwelling that is not accessible, such as the door leading down to an unfinished basement...?
Within the dwelling unit, doors intended for user passage through the unit must meet the requirements for usable doors....
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
F206.5 Doors, Doorways, and Gates
Doors, doorways, and gates providing user passage shall be provided in accordance with F206.5....
-
206.5 Doors, Doorways, and Gates
Doors, doorways, and gates providing user passage shall be provided in accordance with 206.5....
-
Doors, Doorways and Gates [§206.5 and §404]
Doors, Doorways and Gates [§206.5 and §404] Compliance is required for doors, doorways, and gates providing user passage on accessible routes....
-
R218 Doors, Doorways, and Gates
R218 Doors, Doorways, and Gates The SNPRM would revise R218 to read as follows: R218 Doors, Doorways, and Gates....
-
Open Doors Organization (ODO)
Open Doors Organization (ODO), a 501(c)(3) non-profit organization based in Chicago, Illinois was founded in 2000 for the purpose of creating a society in which all persons with disabilities...
-
404.2.7 Door and Gate Hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4....
-
1010.2.2 Hardware
Door handles, pulls, latches, locks and other operating devices on doors required to be accessible by Chapter 11A or 11B shall not require tight grasping, tight pinching or twisting of the...
-
11B-809.8.3 Door maneuvering clearance.
At the dwelling unit side of the primary entry doors, secondary exterior doors, and required exit doors maneuvering clearances shall be 44 inches (1118 mm) minimum in length measured...
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
Door and Signal Timing for Hall Calls [4.10.7], Door Delay for Car Calls [4.10.8]
Timing, based on the distance between the farthest call button and the elevator door, begins with visible and audible signaling of car arrival....
-
IS ASSISTANCE REQUIRED?
[See subsections ...]
-
Solutions to Enhance Wayfinding (slides 8 -15)
[See subsections ...]
-
Eunice Noell-Waggoner, IES, LC. Value, Contrast and Reflections
(Note: A transcript of this presentation was not available. These edited Proceedings are based on notes by JEW and TOS, and slides that accompanied the presentation) Exterior...
