Within thirty days of receiving a complaint, a written response, approved by MOD and signed by both the ADA Coordinator and the department head, is sent to the complainant....
Search Results "Head Height"
-
4. Grievance Procedure
-
Tips on Completing Emergency Health Information
My disability, due to a head injury, sometimes makes me appear confused or drunk. I have a psychiatric disability. In an emergency, I may become confused or overwhelmed....
-
DEPARTMENT OF TRANSPORTATION DISABILITY LAW GUIDANCE: Origin-to-Destination Service
These activities would come under the heading of “fundamental alteration” or “undue burden.”...
-
"Video Remote Interpreting" (VRI) Services (Section-by-Section Analysis)
Several major organizations requested a requirement to include the interpreter's face, head, arms, hands, and eyes in all transmissions....
-
Excel Dryer, Inc. XLERATOReco® Hand Dryer
GREENSPEC® Listed and Helps Qualify for several LEED®credits Virtually Maintenance Free Specifications Dimensions: Width 11 3/4" (298 mm) Height...
-
LaCantina Contemporary Clad Slider System
profiles to suit any architectural style Standard anodized and painted finishes with additional custom color options Self-draining Weather Resistant Sill with interior stop height...
-
3.1 Refining MDE Definition and Committee Scope
., controls to raise and lower the head and foot areas, controls to raise and lower the height of the entire bed, mattresses with circulating air to prevent pressure ulcer development)....
-
1124B
The maximum pile height shall be 1/2 inch (12.7 mm). See Figure 11B-7E(b)....
-
2. Equipment Clearances for Breast Platforms
The manufacturer also raised concerns with the size of the knee and toe clearance and recommended basing the requirements in relation to the height of the breast platform....
-
Philips Healthcare
• Refer to Pages 2 & 3 of this ballot. 2) NPRM M301.2.1 and M302.2.1: Table Height:– Section 5.1 • Refer to separate document from four medical diagnostic imaging equipment industry...
-
Expert opinion on the current knowledge
Transfer boards are a common aid used to facilitate transfers for those who have limited arm strength and/or situations where the height differential between the initial and target seats...
-
Camp Shelters
This height must be maintained for a length of at least 48 inches (1,220 millimeters) beside the clear space so that someone using a wheelchair or other assistive device can transfer to...
-
ASME
The maximum permitted height for operable parts is consistent with Section 308 of this document. The standard also addresses attendant operation....
-
EVAC+CHAIR® 600H Stair Evacuation Chair with Lift Handles
Width: 23" Folded Size: Height = 47" Depth = 12" Width = 23" Weight: 24 lbs...
-
EVAC+CHAIR® 300H (MK-4) Evacuation Chair
Height = 41" Depth = 8" Width = 20" Weight: 19 lbs...
-
Pilot Rock WPTS Square Frame Table Using Recycled Plastic
Nominal seat height is 18". The 8 ft. tables are ADA COMPLIANT....
-
Allegion Falcon 2390 Series Recessed Exit Device
Rod length requirement varies with device mounting height....
-
Excel Dryer, Inc. XLERATOR® Hand Dryers
Solution Over a Decade of Proven Performance Virtually Maintenance Free Specifications Dimensions: Width 11 3/4" (298 mm) Height...
-
Allegion Falcon 1590 Series Exit Devices
Pushbar height is 3" Stile: 2" minimum Electric Functions: EL - electric latch retraction, include "S". Requires PS873-2 minimum power supply....
-
Pilot Rock WPTS Square Frame Table Using Lumber
Nominal seat height is 18". The 8 ft. tables are ADA COMPLIANT....
-
AJW Architectural Products UG130-Railing UG130X-Y108 108" Exposed Flange, 1.5" Diameter Grab Bar, Peened Grip - Configuration Y
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG3-Railing UG3X-Y108 108" Concealed Snap Flange, 1.5" Diameter, Peened Grip - Configuration Y
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
