In order to get an image with sufficient detail, a woman’s breast must rest on top of the breast platform and her chest wall needs to be flush with the front edge of the breast platform....
Search Results "Curb Ramp Top Landing"
Filters
Commonly Searched Documents
-
4.4.3 Implications of Mammography Equipment Components
-
404.2.10 Door and Gate Surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
AN INCREASING NUMBER OF HEALTH CARE PROVIDERS ARE TRANSITIONING TO ADJUSTABLE HEIGHT TABLES
Some tables may require installation of a modified top to meet the 19” standard but would not require changing out the installed base....
-
5.1 Transfer Surface Height Recommendations
The height of the transfer surface during patient transfer shall be 17 inches minimum and 19 inches maximum measured from the floor to the top of the transfer surface....
-
Initial Measures and Transfer Setup
The device seat to floor height was measured as the linear distance between the front of the seat, center-line point on top of the cushion (if present) and the floor (Figure 3 left). ...
-
STEP 2: TELL YOUR ARCHITECT AND BUILDING CONTRACTOR THAT YOU EXPECT YOUR NEW FACILITY TO COMPLY WITH THE ADA.
Emphasize with your architect, your designer, your building contractor, and franchise design and construction staff that ADA compliance is a top priority....
-
Public Address Systems and Microphones
spoken into) where multiple microphones are used For best results, participants should be sure to use microphones and speak one at a time, talk close to microphones "across" the top...
-
2. b. ii. Accessible Door Hardware
Hardware required for accessible door passage shall be mounted no higher than 48 in (1220 mm) above finished floor. xv Figure 14 and 15 (top and bottom left) Non-accessible door...
-
4.34.4 CONSUMER INFORMATION
(4) Identification of the location of any equipment and parts required for adjusting or replacing counter tops, cabinets, and sinks....
-
II. DISCUSSION
If ADAAG 904.4.1’s 36-inch length requirement does apply, does a defendant violate this requirement by maintaining merchandise or other items on the counter top, thereby failing to maintain...
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
1136A.1 Receptacle heights
Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located no more than 48 inches (1219 mm) measured from the top of the...
-
11B-809.12 Electrical receptacles, controls and switches
amperes or less, communication system receptacles, controls and switches shall be located as follows: Where there is no obstruction, 48 inches (1219 mm) maximum measured from the top...
-
11B-404.2.10 Door and gate surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
Key Differences Between Routes
Interior accessible routes may include corridors, floors, ramps, elevators, lifts, and clear floor space at fixtures....
-
II. Rulemaking History
These accessibility requirements relate to, among other things, ramps and lifts, onboard circulation, wheelchair spaces and securement devices, priority seats, stop request systems, and...
-
Wikk Industries Inc. Bollard With Push Plate PART # BPFSMPREP36PCCL
Welded Flat top(FT)....
-
What other surface considerations affect wheelchair travel?
Although the slip resistance ratings of carpet fall within the recommended ranges for use on ramps, its rolling resistance makes most types an inappropriate finish for sloped surfaces....
-
Key Study findings:
One two-step transfer included a ramp in between two platform steps whereas the other two-step transfer had no ramp or space between the first and second platform steps....
-
1. Sloped Surfaces
Sloped Surfaces Measuring the slope of a ramp, parking space, walkway, or other ground or floor surface is important to identify whether the surface is accessible....
-
1.1.4 Walk cross slope
Slopes greater than 1:20 are considered ramps and must conform to the requirements for ramps....
-
11B-307.3 Post-mounted objects
Exception: The sloping portions of handrails serving stairs and ramps shall not be required to comply with Section 11B-307.3....
-
382.97 To which aircraft does the requirement to provide boarding and deplaning assistance through the use of lifts apply?
At U.S. airports where lift or ramp boarding is required, the requirement applies to aircraft with 19 or more passenger seats, with a few stated exceptions....
-
Play Components
For the purpose of the guidelines, ramps, transfer systems, steps, decks, and roofs are not considered play components....
