The door maneuvering clearance must be measured from the leading edge of such elements so that the full clearance is free of any obstruction....
Search Results "Unit of Measurement"
-
Can handrails overlap door maneuvering clearances?
-
11B-603.6 Guest room toilet and bathing rooms
that are not required to provide mobility features complying with Section 11B-806.2 shall provide all toilet and bathing fixtures in a location that allows a person using a wheelchair measuring...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
Accessible Ground Surfaces
This standard assesses the accessibility of a surface by measuring the work an individual must exert to propel a wheelchair across the surface....
-
R210.3 Shared Use Paths
Objects shall not overhang or protrude into any portion of a shared use path at or below 2.4 m (8.0 ft) measured from the finish surface....
-
Chapter M3 Technical Criteria
The technical criteria specify measurements in inches and millimeters....
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured between an entrance and all vehicular or pedestrian...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
due to unusual characteristics of the site when: The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
Appendix Two: Design Information and Accommodation Models
Research findings on Eye Height, measured on the right eye Type of WhMD user Sam-ple Size Mean (SD) Min 5%ile 10%ile Me-dian 90%ile...
-
2.4.1 Current Marketplace Dynamics
Notes I The methods for measuring “low heights” for current height adjustable products vary among manufacturers and product designs. No official measurement method currently exists....
-
Base Support [No specific provision—affects M303.2.4]
The footrest height data measures the height from the floor to the top surface of the footrest at its proximal outside corner....
-
A MINIMUM HIGHEST POINT STANDARD OF 19 INCHES IS CONSISTENT WITH EXISTING ACCESSIBILITY STANDARDS
The height of water closet seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the floor, measured to the top of the seat....
-
Knee & Toe Space [M303.2.4]
Each of these measurements creates a more accessible piece of imaging equipment balanced with the physical attributes and operation of the equipment....
-
Social Security Administration Guide: Alternate Text for Images
The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government, and shall not be used for advertising or product endorsement...
-
IV. REPORTING, ENFORCEMENT, AND OTHER PROVISIONS
Private Plaintiffs and the United States shall not unreasonably withhold such approval. 41....
-
4(2)(b)
(b) Design features such as sunken or raised functional areas do not interrupt the accessible route through the remainder of the dwelling unit....
-
9.2.2 Minimum Requirements
An accessible unit, sleeping room or suite shall be on an accessible route complying with 4.3 and have the following accessible elements and spaces....
-
4.24.1 GENERAL
Sinks in kitchens of accessible dwelling units shall comply with 4.34.6.5....
-
§100.20 State
State means any of the several states, the District of Columbia, the Commonwealth of Puerto Rico, or any of the territories and possessions of the United States....
-
8. Notice, Reporting, and Monitoring Requirements
If the United States believes that Cinemark is not in compliance with this Consent Order or any requirement contained herein, the United States agrees to notify Cinemark in writing of the...
-
J. Other Provisions
The United States may review MSHA’s compliance with this Agreement or Title III of the ADA at any time. ...