Where installed in wet locations, the surface of the seat shall be slip resistant and shall not accumulate water....
Search Results "Seat Height"
Filters
Commonly Searched Documents
-
11B-903.7 Wet locations
-
Dimensions and Capitalization: ADA Standard Section 703.3.1
two dots in the same cell 1 0.090 (2.3 mm) to 0.100 (2.5 mm) Distance between corresponding dots in adjacent cells 1 0.241 (6.1 mm) to 0.300 (7.6 mm) Dot height...
-
703 Signs
Requirements for signs provide specifications for raised characters (703.2), braille characters (703.3), the height and location of signs with tactile characters (703.4), visual characters...
-
Toilet Paper Dispensers
Requirements for toilet paper dispensers in section 604.7 include specifications for height....
-
3.3.15.1 Forward reach – unobstructed
Lower percentages in a forward reach for scooter users partially resulted from having to overcome a greater distance to reach over and/or around the front tiller, particularly at lower heights...
-
Protruding Objects
All objects that protrude from surfaces or posts and all overhanging objects in areas where people walk shall comply with the following requirements: Objects mounted on walls at a height...
-
Dispersion Requirements
In the final rule, it is required that wheelchair spaces be dispersed so that persons using them have "choices of seating locations and viewing angles that are substantially equivalent to...
-
§ 38.77(c)
(c) At all doors on level-entry vehicles, and at each entrance accessible by lift, ramp, bridge plate or other suitable means, handrails, stanchions, passenger seats, vehicle driver seat...
-
R410.9 Character Spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
703.5.8 Character Spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
R405.3.4 Clearance Reduction
Between 230 mm (9 in) and 685 mm (2.25 ft) above the finish surface, the knee clearance shall be permitted to reduce at a rate of 25 mm (1 in) in depth for each 150 mm (6 in) in height....
-
Do drinking fountains pose hazards as protruding objects?
Cantilevered units at standard heights for people who stand must be recessed or protected as protruding objects....
-
1.7 Cross-Aisle
1.7 "Cross-Aisle" shall mean and refer to a pathway between sections of seats that is parallel to the theater screen....
-
§382.27(c)(7)
(7) Provision of an on-board wheelchair on an aircraft with more than 60 seats that does not have an accessible lavatory....
-
University of Louisville, Injury Risk Assessment and Prevention (iRAP) Laboratory
of wheelchair transportation safety, investigators utilize computer modeling and sled impact testing to gain and understanding of injury risk when using a wheelchair as a motor vehicle seat...
-
11B-608.2.2.1 Clearance
minimum side of the clearance provided that it is not on the side of the clearance adjacent to the controls or, where provided, not on the side of the clearance adjacent to the shower seat...
-
11B-803.5 Coat hooks and shelves
Coat hooks shall not be located above the bench or other seating in the room. [2010 ADA Standards] 803.5 Coat Hooks and Shelves....
-
Character Specifications
For characters with rectangular cross sections, a stroke thickness of 10% to 15% of the character height was specified (based on the uppercase "I")....
-
Doors in a Series
The height of door and gate hardware (34 to 48 inches) is specified in section 404.2.7....
-
UDI
Forward reach was measured similarly from the point where the seat back meets the seat....
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
Introduction
Footrest clearance height and depth...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...