Development of Surface Roughness Standards for Pathways used by Wheelchairs. Presented at Transportation Research Board Annual Meeting. Washington D.C....
Search Results "Reflecting Surface"
Filters
Commonly Searched Documents
-
6. Dissemination Activities
-
1009.3.1 Sloped Entries
EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
-
1009.3.1 Sloped Entries
EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip resistant....
-
T503.4 Steps at Other Doorways
The walking surface on steps serving all other non-rail vehicle doorways shall be lighted at all times with 2 foot-candles (22 lux) minimum of illumination....
-
903.5 Height
The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground....
-
5.3.3.1 Height
The total height of the toilet seat on the riser for a pit toilet shall be between 17 inches (430 mm) and 19 inches (485 mm) above the floor or ground surface....
-
1011.2 Clear Ground Space
This section requires a clear ground space to be provided at outdoor constructed features and includes specific provisions for the size and location (1011.2.1), surface (1011.2.2), slope...
-
4.34.6.5(8)
(8) There shall be no sharp or abrasive surfaces under sinks. Hot water and drain pipes under sinks shall be insulated or otherwise covered. Figure 51 Kitchen Sink...
-
5.3.3.1 Height
The total height of the toilet seat on the riser for a pit toilet shall be between 17 inches (430 mm) and 19 inches (485 mm) above the floor or ground surface....
-
Garage Parking
At sites that also include surface lots, a garage is treated as a separate parking facility for scoping purposes....
-
1133A.7.1 Plumbing protection
There shall be no sharp or abrasive surfaces under kitchen sinks....
-
1133A.7.1 Plumbing protection
There shall be no sharp or abrasive surfaces under kitchen sinks....
-
Ruderman Family Foundation
The work of the Ruderman Family Foundation reflects our core values of social justice, innovation, collaboration, and agility. ...
-
Alterations
Section 226.1, exempts sales and service counters from the technical requirements of 902 (dining surfaces and work surfaces)....
-
Literature Review
The first review of the literature focused on the effects of surface roughness on the health and safety of WC riders....
-
R409.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 32 mm (1.25 in) minimum and 51 mm (2 in) maximum....
-
T502.3.2 Thresholds
The stripe shall be 1 inch (25 mm) wide minimum and contrast with the rest of the walking surface either light-on-dark or dark-on-light....
-
1134A.8, Item 6
There shall be no sharp or abrasive surfaces under lavatories....
-
4.8.5(2)
(2) If handrails are not continuous, they shall extend at least 12 in (305 mm) beyond the top and bottom of the ramp segment and shall be parallel with the floor or ground surface (see Fig...
-
11B-812.7.3 Lettering
The words “NO PARKING” shall be painted on the surface within each access aisle in letters a minimum of 12 inches (305 mm) in height and located to be visible from the adjacent vehicular...
-
TRANSIT BOARDING PLATFORM
[DSA-AC] A horizontal, generally level surface, whether raised above, recessed below or level with a transit rail, from which persons embark/disembark a fixed rail vehicle....
-
1134A.8, Item 6
There shall be no sharp or abrasive surfaces under lavatories....
-
TRANSIT BOARDING PLATFORM
[DSA-AC] A horizontal, generally level surface, whether raised above, recessed below or level with a transit rail, from which persons embark/disembark a fixed rail vehicle....
-
11B-812.7.3 Lettering
The words “NO PARKING” shall be painted on the surface within each access aisle in letters a minimum of 12 inches (305 mm) in height and located to be visible from the adjacent vehicular...
