To see the entire Chapter, consult California Code of Regulations, Title 24, Part 2 - 2022 California Building Code (2022 CBC), available for purchase from International Code Council (http...
Search Results "Grade 2 Braille"
Filters
Commonly Searched Documents
-
1.9.1.8 Adopting agency identification
-
11B-801.1 Scope
The provisions of Division 8 shall apply where required by Division 2 or where referenced by a requirement in this chapter. Advisory 11B-801.1 Scope....
-
11B-903.1 General
This section provides the technical provisions for benches required to comply with Division 2 Scoping Requirements -- those in saunas, steam rooms, dressing, fitting and locker rooms, holding...
-
PUBLIC ENTITY
[ADA Title III §36.104] Public entity means— (1) Any State or local government; (2) Any department, agency, special purpose district, or other instrumentality of a State or States...
-
11B-407.2.1.5 Signals
[2010 ADA Standards] 2. Existing elevators shall not be required to comply with 407.2.1.5....
-
Minimum Number of Accessible Parking Spaces
Van-Accessible Parking Spaces with min. 96" wide access aisle Accessible Parking Spaces with min. 60" wide access aisle 1 to 25 1 1 0 26 to 50 2...
-
404.2.5 Thresholds
Thresholds, if provided at doorways, shall be 1/2 inch (13 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with 302 and 303....
-
404.2.5 Thresholds
Thresholds, if provided at doorways, shall be 1/2 inch (13 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with 302 and 303....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
1.3 General Exceptions
requirements in 11B-203.2 Many of these exceptions are applicable to public school, community college and higher education projects; a copy of Section 11B-203 is provided as Attachment 2...
-
Big John Original Toilet Seat Open Front w Cover (White) - 3W
The seat is made from the highest grade of ABS plastic which is both stain and chemical resistant. Stainless steel hinges provide unbreakable strength....
-
Voluntary Barrier Removal vs required Barrier Removal
If an existing 2 story retail building which is exempt from installing an elevator chooses to do so, is he exempt from POT upgrades for altered areas?...
-
11B-604.5.2 Rear wall
The Office of Statewide Health Planning and Development (OSHPD), which has jurisdiction over hospitals and long-term care facilities in California, issued Code Application Notice CAN 2-...
-
2.2.6 Door Use
The door characteristics are summarized in Table 2‒3. Table 2‒3. Characteristics of doors tested. ...
-
Minimum Number [9.1.2 and 9.1.3]
VISUAL APPLIANCES ONLY Total MOBILITY ACCESS & VISUAL APPLIANCES Total (portion of total with roll in showers) 1‒25* 1 1 26‒50 2...
-
Raised Characters
The proposed rule, consistent with the original ADAAG, specified a character height between e inch and 2 inches....
-
QUALIFIED INTERPRETERS
., where the interpreter is not familiar with the specialized vocabulary involved in the communication at issue. (2) 2. There are a number of different sign language systems....
-
4.10.4 HALL LANTERNS
(2) Visual elements shall be at least 2-1/2 in (64 mm) in the smallest dimension. (3) Signals shall be visible from the vicinity of the hall call button....
-
11B-212.3 Sinks
ETA Editor's Note The definition of "Sink" in CBC Chapter 2, adopted by DSA-AC, is as follows: SINK....
-
11B-407.2.2.1 Visible and audible signals
Reserved. 2. Reserved. [2010 ADAS] 2. In existing elevators, a signal indicating the direction of car travel shall not be required....
-
404.2.5 Thresholds
Thresholds, if provided at doorways, shall be 1/2 inch (13 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with 302 and 303....
-
1134A.8, Item 4.3
The knee and toe space shall be centered on the fixture, and shall comply with Section 1138A.2....
-
1134A.8, Item 4.3
The knee and toe space shall be centered on the fixture, and shall comply with Section 1138A.2....
-
1.2.7
1.2.7 When local variations (flatness) for cross slope of ramps are measured according to 1.1.14 at least 80% (rounded to the nearest whole number) should not exceed a 2% slope....
