The diameter or width of the gripping surfaces of a handrail or grab bar shall be 1‒1/4 in to 1‒1/2 in (32 mm to 38 mm), or the shape shall provide an equivalent gripping surface....
Search Results "Shower Grab Bar"
Filters
Commonly Searched Documents
-
4.26.2* Size and Spacing of Grab Bars and Handrails
-
5.3.4 Grab Bars
Where walls or partitions are provided, grab bars complying with ABAAS section 604.5 shall be provided....
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall. ...
-
AJW Architectural Products US130-A Series US130-A12 12" Exposed Flange, 1.5" Diameter Security Grab Bar - Configuration A
Grab bars must be installed properly to support the loads intended....
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall. ...
-
604.9.4 Grab Bars
Grab bars for water closets shall comply with 604.5....
-
604.9.4 Grab Bars
Grab bars for water closets shall comply with 604.5....
-
8. Gap
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
Location
When this grab bar was used (e.g....
-
11B-604.8.2.3 Grab bars
11B-604.8.2.3 Grab bars. Grab bars shall comply with Section 11B-609. A side-wall grab bar complying with Section 11B-604.5.1 shall be provided on both sides of the compartment....
-
§ 38.123(a)(3)
(3) A grab bar at least 24 inches long shall be mounted behind the water closet, and a horizontal grab bar at least 40 inches long shall be mounted on at least one side wall, with one end...
-
AJW Architectural Products UG130-A Series UG130-A12 12" Exposed Flange, 1.5" Diameter Grab Bar - Configuration A
Installation: Before installing grab bars, verify with all state and local codes for requirements on bar diameter and type finish....
-
AJW Architectural Products UG120-A Series UG120-A12 12" Exposed Flange, 1.25" Diameter Grab Bar - Configuration A
Installation: Before installing grab bars, verify with all state and local codes for requirements on bar diameter and type finish....
-
11B-604.9.4 Grab bars
11B-604.9.4 Grab bars. Grab bars for water closets shall comply with Section 11B-604.5....
-
Moen Stainless 30" Grab Bar
complies with Americans with Disabilities Act (ADA) specifications 30" bar length 1.25" bar diameter corrosion resistant stainless steel construction for added durability limited...
-
(1)(c)
(c) A grab bar at least 24 inches (610 mm) long should be mounted behind the water closet, and a horizontal grab bar at least 40 inches (1015 mm) long should be mounted on at least one side...
-
11B-609.6 Fittings
Grab bars shall not rotate within their fittings....
-
609.6 Fittings
Grab bars shall not rotate within their fittings....
-
609.6 Fittings
Grab bars shall not rotate within their fittings....
-
609.6 Fittings
Grab bars shall not rotate within their fittings....
-
11B-609.6 Fittings
Grab bars shall not rotate within their fittings....
-
AJW Architectural Products UG3-A Series UG3-A12 12" Concealed Snap Flange, 1.5" Diameter Grab Bar - Configuration A
Bars with greater offsets will support loads up to 250lbs when properly installed....
-
AJW Architectural Products UG2-A Series UG2-A12 12" Concealed Snap Flange, 1.25" Diameter Grab Bar - Configuration A
Bars with greater offsets will support loads up to 250lbs when properly installed....
-
11B-604.8.2.3 Grab bars
Grab bars shall comply with Section 11B-609. A side-wall grab bar complying with Section 11B-604.5.1 shall be provided on both sides of the compartment....
