Control buttons shall be 3/4 inch (19 mm) minimum in their smallest dimension....
Search Results "Absolute Dimension"
-
409.4.6.1 Size
-
A. Measuring Slope and Cross Slope
Now, take the tape measure and measure the open gap at the downhill end of the level, as shown in the photo opposite - this the "critical dimension"....
-
5.1.3 Transfer Surface Low Height Options for M301 and M302
Members focused on determining a specific low height absolute measurement. A portion of the Committee recommended a height range of 17 inches to 25 inches....
-
A. Finish and Contrast
Note that in any application both white and black are never absolute; thus, B never equals 100 and B is always greater than 0....
-
Introduction
Introduction The following memo is a brief analysis of the wheelbase dimension for wheeled mobility devices in the anthropometry of wheeled mobility database....
-
11B-409.2 Call buttons
Call buttons shall be ¾ inch (19.1 mm) minimum in the smallest dimension and shall comply with Section 11B-309....
-
409.2 Call Buttons
Call buttons shall be 3/4 inch (19 mm) minimum in the smallest dimension and shall comply with 309....
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
§ 38.125(b)(2)(ii) Exception
Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the car axis, the transportation entity may specify a lift...
-
§ 38.83(b)(2)(ii) Exception
Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the vehicle axis, the transportation entity may specify a lift...
-
§ 38.95(b)(2)(ii) Exception
Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the car axis, the transportation entity may specify a lift...
-
409.2 Call Buttons
Call buttons shall be ¾ inch (19 mm) minimum in the smallest dimension and shall comply with 309....
-
11B-409.2 Call buttons
Call buttons shall be ¾ inch (19.1 mm) minimum in the smallest dimension and shall comply with Section 11B-309 _|Operable Parts|_....
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
4.10.12(1)
All control buttons shall be at least 3/4 in (19 mm) in their smallest dimension. They shall be raised or flush....
-
4.10.12(1)
All control buttons shall be at least 3/4 in (19 mm) in their smallest dimension. They may be raised or flush....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
-
11B-409.2 Call buttons
Call buttons shall be ¾ inch (19.1 mm) minimum in the smallest dimension and shall comply with Section 11B-309 _|Operable Parts|_....
-
Seeger et al.
Both unoccupied and occupied dimensions of device width and length were measured as well as a set of other basic dimensions....
-
304 Turning Space
Comments urged that the minimum dimensions for turning space be increased to better accommodate scooters and motorized wheelchairs....
-
Clearance Around Base (M301.4.2 and M302.4.2)
Comments are requested on the following questions regarding the proposed dimensions for clearance around the base of the equipment to allow the use of portable floor lifts: a) Are the...
-
§382.133(e)(2)
(2) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with FAA safety requirements...
-
407.2.1.2 Size
Call buttons shall be ¾ inch (19 mm) minimum in the smallest dimension. EXCEPTION: Existing elevator call buttons shall not be required to comply with 407.2.1.2....